Search

New vent for the model 290, 290A, and 290B lanterns. 

Fits all 290 and 295 model lanterns

Brass burner tube for the 214 lanterns.

Steel burner tube for the 214 lantern.

This is a new Coleman made generator for Model 290, 290A and 295 Lantern. Each includes new gas tip, spring, and cleaning needle.
This generator can be used on the 290 series lanterns, but you will have to use your original generator nut instead of the new one that comes with this generator. The 290 generators have been discontinued.  
These are also known as part number 3000005404 and replaces the 290 & 290A part number of 290-5891.

This is a Coleman made new valve assembly that fits the 290 and 290A model lanterns. These have a metal eccentric block, feed tube, new knob and screw included.

Used collar for the model 290-700 lantern. Has red around the center circle rather than black.

Used collar for the model 290A700T lantern. 

Used collar for the 290 lantern. Has a black circle around the center hole rather than red.

These fit all 290 and 295 model lanterns.
  - The 290 was originally made with a full frame and did not come with a heat shield, so this version is a bit of work to get installed. Once in place, it ends up covering the lighting holes in the bottom of the frame - FYI.
  - On a 290A and 295, you will need to replace the frame bottom also if yours has riveted in springs.

Used collar for the model 290A700 lantern. Has red around the center circle rather than black.

Lighting stem.

Fits models 290, 290A, 290B and 295, 295A.

This is for models 286A, 288, 288A, 290 and 290A

Parts Diagrams HERE.

New green carry case for models 200A, 288, 286, 290, 290A, 295, 220 F-K, 321, 327, 427 and QuickLite Lanterns.

Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.

Fits 285, 288, 290 and 295 model lanterns. 

These are used and will vary in wear.

This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

This is a US made Pyrex replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.

Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.

Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.

This product is not included in the OCP free shipping program.

Photo's with lanterns are for illustration purposes only.

Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.

Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.

This is a used Century Primus globe 8936 made by Schott Suprax Glas made in West Germany. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Has a spot that looks glued or burnt on (see photos)

This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Burner assembly with brass burner tubes

Used Burner assembly with brass burner tubes - wear will vary

These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.

Need more information on the valve core? Click HERE.

Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns. 

Will all vary in wear and some may have rust .

Same as part number 288-1251

Compatible with 635 and the 621 series lanterns. This is a reproduction part.

Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns. 

Fits the fuel tube on all appliances that have a plastic fuel and air tube.  

Models: 214, 282, 285, 288, 290, and 295.

Also fits: 

• The fuel tube on the 550B stove
• On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251

New feed tube assembly made by Coleman. Includes new Schrader valve and O-ring. Fits all 282, 285, 286, and 288 model lanterns.

Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.

Reproduction nickel plated vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.

This is a used ball nut for the 247, 249, and 242 Lanterns - except it will not fit the 242 No Letter / Junior.

This is a used bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Will show wear and rust and such, but be solid.

This is a very nice reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Made of spring steel here in the USA.

Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.

Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.

New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.

This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.

Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

New filler cap screw for the small 242 & 249 lanterns and 500 stove size filler caps.

Reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Looks identical to the original.

These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.

This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.  

Comes with a new gasket for you to installed if needed.

Used brass filler cap. Will all vary in wear and amount of brass faded. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.

Will come with a new gasket for you to install if needed.

Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.

They will all show varying signs of wear.