Search

Search type
Search in:
20 products found
  • 242 Vent Pin - R629

    Brass Pin for 242 or 242NL Lantern - will not fit other versions of the 242. This is secured directly to the 242 vent. This fits into the burner frame hole - It forms to the 242 vent and captures it permanently after you heat it and swedge it in place. See directions below. Comes with Steel rod to assist in the process.

    Installing Pin into a 242 vent:

    1. Position the steel shaft with the hole end up in a vise securely. 
    2. Put the brass pin insert in the hole of the big shaft. 
    3. Heat the small lip of the brass insert with a propane torch until it's a nice orange color, this will anneal it and make the brass softer so it won't crack when it's tapped over. 
    4. Set the vent over the insert. 
    5. Place a ball peen hammer or something with a similar on the heated lip of the pin.
    6. Tap down with a hammer onto the center and gently tap it with another hammer to swedge it outward - continue until it's seated nicely in the vent.

    You will notice the edges of the lip will fall away.


    0.0
    Add first review
    Not rated yet
    • $24.25
    Sorry, we only have 1 of that item available
  • 243 Vent Pin - R628

    Brass Vent Bolt for 243, and 243A Lantern - this screws down into the top of the frame for the 243 vent to sit on.

    0.0
    Add first review
    Not rated yet
    • $14.50
    Sorry, we only have 4 of that item available
  • 242 Vent Finish Bolt - R627

    Brass bolt for 242 or 242NL Lantern - will not fit other versions of the 242. This is just for the top brass bolt.

    0.0
    Add first review
    Not rated yet
    • $10.30
    Sorry, we only have 6 of that item available
    • New!

    440 Mica Globe - G12

    This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.

    0.0
    Add first review
    Not rated yet
    • $48.00
    Sorry, we only have 8 of that item available
  • Generator Spring, Used - S98

    Used generator spring for 200, 200A, 242, 243, 202 & Similar Sears Lanterns. This is the older style.

    0.0
    Add first review
    Not rated yet
    • $5.00
    Sorry, we only have 12 of that item available
  • Generator Spring - R578

    Reproduction generator spring for 200, 200A, 242, 243, 202 & Similar Sears Lanterns.

    0.0
    Add first review
    Not rated yet
    • $6.50
    Sorry, we only have 83 of that item available
  • Generator for 200/242, Reproduction - R200

    Reproduction Generator for 200, 200A, 202, 242, 243, 243A & Similar Sears Lanterns. New generator includes new gas tip, spring, and tip cleaning wire. The generator is complete and you need nothing else for the install.
    Same as the old part numbers T66, 200A2891 and 3000005089.

    0.0
    Add first review
    Not rated yet
    • $18.80
    Sorry, we only have 423 of that item available
  • Pump Assembly, Universal - C045

    Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

    Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

    0.0
    Add first review
    Not rated yet
    • $13.35
    Sorry, we only have 74 of that item available
  • Tip Cleaner Stem Reproduction - R651

    Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247 and similar lanterns. Also fits the 523 and the 520/M1941 stove.

    0.0
    Add first review
    Not rated yet
    • $14.55
    Sorry, we only have 345 of that item available
  • Pump Assy Leather Used Push On Nut - U811

    This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

    0.0
    Add first review
    Not rated yet
    • $12.00
    Sorry, we only have 12 of that item available
  • 200 Burner Frame Washer Kit - K14

    These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.

    New 200 burner frame Pal Nut is HERE.

    New 200 burner frame Nut is HERE.

    0.0
    Add first review
    Not rated yet
    • $2.05
    Sorry, we only have 3782 of that item available
  • Pump Cup & Nut, Neoprene - C008

    Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
    Also known as part number 6391091

    0.0
    Add first review
    Not rated yet
    • $5.10
    Sorry, we only have 151 of that item available
  • Pump Assembly Neoprene Used - E1561

    Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 


    0.0
    Add first review
    Not rated yet
    • $7.00
    Sorry, we only have 5 of that item available
  • Burner Cap - 200/242 - C009

    This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242  and 247 lanterns. Also fits a few lamps and Sears lanterns.
    Also known as part number 2423231.

    0.0
    Add first review
    Not rated yet
    • $6.60
    Sorry, we only have 94 of that item available
  • Valve Stem Retaining Ring - 1/4" - S04

    This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

    0.0
    Add first review
    Not rated yet
    • $3.70
    Sorry, we only have 14 of that item available
  • Gas Bottle, 8 oz. - R321

    This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

    0.0
    Add first review
    Not rated yet
    • $5.75
    Sorry, we only have 14 of that item available
  • Check Valve With Stem - C001

    This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

     If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

    5.0
    Score: 5.0 (votes: 1)
    Reviews: 1
    • $12.80
    Sorry, we only have 490 of that item available
  • Check Valve Removal Tool, Universal - R701

    This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.

    C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
    R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves. 

    0.0
    Add first review
    Not rated yet
    • $81.00
    Sorry, we only have 73 of that item available
  • Generator for 201/241/247 - C022

    New Generator for 201, 241 and 247 Kerosene Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
    Also known as part number 242K289, 201B5891 and 3000005402.

    5.0
    Score: 5.0 (votes: 1)
    Reviews: 1
    • $24.60
    Sorry, we only have 69 of that item available
    • 49% less

    Generator Spring 201, Used - E1211

    Used Aluminum Generator Spring for 201, 241 and 247 Kerosene Lanterns.

    All will vary in wear.

    0.0
    Add first review
    Not rated yet
      • 49% less
      Market price:$9.75 you save $4.75
    • $5.00
    Sorry, we only have 1 of that item available

Footer navigation