- New!
Ball Nut, Brass - S121
These are reproduction brass ball nuts. This is the common sized ball nut used on most Coleman lanterns.
These are reproduction brass ball nuts. This is the common sized ball nut used on most Coleman lanterns.
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is a used Pyrex old red letter logo replacement globe used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a burn mark and one small spot missing the amber (see photos)
These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. Red globes are "Made in U.S.A." Very rare and hard to find.
This one has a manufacturer defect (shown in photos). The defect is just a distortion and came that way from the factory.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap off the Model 200A burgundy.
Comes with a new gasket that you will have to install.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a used old style burner frame originally used on the black band 200A Lantern. Looks like someone may have replaced the tabs - they are supposed to be short.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a few imperfections in the glass, color is faded and has one burn mark (see photos)
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
This is a used unmarked straight globe that will fit many single mantle lanterns. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. This is a Fred Kuntz reproduction. Glass measures 3 1/2" Wide X 4" Tall.
New old stock Optimus Globe - Made in West Germany by Jenaer Suprax Glas. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 249 and other similar sized Lanterns.
This is a used 242 Optimus Globe. It will fit models 200, 200A, 200B, 201, 202, 234, 242A, 242B, 242C, 243, 243A, 247 and 249.
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
Used, black filler cap with lanyard - in good shape. Comes with new lanyard. Comes with a new gasket that you will have to install.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
Also known as part number R690B051.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.