This is the gasket that goes on the 5400-5211 valve stem. It is a small flat washer. Known to fit models 5410A700, but may fit others.
This does not work on the 5430A700 or the 5430B700.
Fuel tube gasket for the model M1950 military stove.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
Filler cap gasket for the model 523 military stove.
Filler plug gasket for the model CQ lamps,327 Quicklite lanterns and many older stoves. Can be used in place of the 104-136 lead gasket. Also fits the 523 military stove.
This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Cap Gasket for M1942 & M1950 stoves.
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
Used filler plug for catalytic heaters, green color. Gaskets seem in really good shape
New gasket for the military lantern parts well cap.
This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.
This fits many applications for propane appliances.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #5
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #9.
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8.
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7.
It has been reported that the 285 valve stem uses 2 of these.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #6
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7
It has been reported that the 285 valve stem uses 2 of these.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8
This has been reported to be the correct size to repair the valve on the 400B and the 533A stoves. One is needed for both.
This is the gasket only from the 5423A5611 small parts kit. OD 1/2", ID 3/16", Thickness is just under 1/16" Was commonly used on the model 5413, 5413A, 5423, 5430B, 5433, 5430B, 5430C, 5435C, 5435D and similar propane stoves.
Filler cap gasket for the Prentiss Waber lantern.
O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone.
It is verified it will fit the 533 Stove - 2 are needed.
Cap gasket for Akron lanterns. Outside diameter is 5/8 of an inch. Inside diameter is 3/8 of an inch. Thickness is 1/8 inch.
New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉.
Sheets are 4-3/4" in diameter and 1/32" thick.
Term-Sport Alcohol Stove Gasket Set. These gaskets are for the filler cap and the burner tube. Both are made from fuel resistant materials that will last for years (ECH - Cap & Viton - Burner Tube).
This is a new gasket for your metal snap on parts safe. Fits the 200A size metal safe. Measures 5 1/4" from outside edge to outside edge of gasket.
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
Filler cap lanyard for the small backpacking lanterns.
This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.
Jug cap that fits most Coleman jugs. Does not have a gasket - this is the cap only. Will need a gasket to seal well.
This is a complete rebuild kit for the pump on an M1942 stove. You will get the cap gasket, check valve dot, and pump leather.
New feed tube assembly made by Coleman. Includes new Schrader valve and O-ring. Fits all 282, 285, 286, and 288 model lanterns.
This is a complete rebuild kit for the pump on an M1950 stove. You will get the cap gasket, check valve dot, fuel tube gasket and pump leather.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
Filler cap insert for the models 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. Also fits the model 500 stove. Will have a new gasket installed.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.
O-Ring sizes are #6, #7, and #9, made of Flourosilicone.
We know it does work on these models: 533, 440, 442
Does not work on the 400B, 508B, 533A, 3024
New Old Stock - Parts well cap for the military lantern. Has a new rubber gasket.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Reproduction filler cap insert for the older winged style filler caps used on model 427 lanterns. Comes with the new gasket.
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
