This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. Red globes are "Made in U.S.A." Very rare and hard to find.
This one has a manufacturer defect (shown in photos). The defect is just a distortion and came that way from the factory.
These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a burn mark and one small spot missing the amber (see photos)
This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
New old stock Optimus Globe - Made in West Germany by Jenaer Suprax Glas. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 249 and other similar sized Lanterns.
This is a used 242 Optimus Globe. It will fit models 200, 200A, 200B, 201, 202, 234, 242A, 242B, 242C, 243, 243A, 247 and 249.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a few imperfections in the glass, color is faded and has one burn mark (see photos)
This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.
This is a new old stock Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. Comes with the red trailblazer logo. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.
This is a used Pyrex old red letter logo replacement globe used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
This fits models 200, 202, 200A,242, 242A, 242B, 242C, 247, 249. and 5101.
This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a used fount for the 200A lantern dated 6-76. This fount as a couple paint chipping/scuffs, overall great condition (see photos)
Used tall style vent for the 200/200A lanterns.
This one has some scratches and paint chipping (see photos)
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a used fount for the model 200A lantern. Has some paint chipping, scratches/scuffs and two very small dents you can only see in certain lights (see photos). Otherwise in nice shape - inside of tank looks good too.
This is a used tall style vent for the 200 and 200A Lantern.
Has some paint chips (see photos)
Used tall style vent for 200/200A lanterns made in 1962 and before. This vent has some rust and chippings (see photos).
New Old Stock parts. Comes with original box.
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
Used short style vent for the 200/200A lanterns.
This vent has some scuffs/scratches and a little paint chipping (see photos).
Used short style vent for 200/200A lanterns. This vent has some paint chipping (see photos)
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
This is a used unmarked straight globe that will fit many single mantle lanterns. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. This is a Fred Kuntz reproduction. Glass measures 3 1/2" Wide X 4" Tall.
Used short style vent for the 200/200A lanterns. Has a some scratches/scuffs and paint chips (see photos).
Used tall style vent for 200/200A lanterns made in 1962 and before. This vent is the slightly darker cherry red and is in great shape. This vent has paint chipping and has very tiny white dots all over it - color looks slightly faded (see photos)
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
New NOS valve stem for the model 200A lantern.
Used short style vent for the 200/200A lanterns made in 1963 and after.
This vent has some scratches/scuffs and paint chippings (shown in photos)
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
This is a used fount for the 200A lantern dated 9-60. Has some scratches/paint chipping and a dent by the pump assembly (see photos)
These mica panels are 3" x 5" in size.
General information:
Used Coleman ceramic burner cap for the 242 and 200A series lanterns. Has "COLEMAN" written on it
They all will vary in wear but will all be in one piece.
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
This is a 10 PACK of the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
Reproduction stainless steel bail handle for the models 202, 200, and 200A.
This is a used one piece filler cap off the Model 200A burgundy.
Comes with a new gasket that you will have to install.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Reproduction Generator for 200, 200A, 202, 242, 243, 243A & Similar Sears Lanterns. New generator includes new gas tip, spring, and tip cleaning wire. The generator is complete and you need nothing else for the install.
Same as the old part numbers T66, 200A2891 and 3000005089.
New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
Also known as part number R690B051.
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.
Used valve stem for the model 200A lantern. Has been cleaned, and packing changed.
