This is a used vent. Has some paint chipping (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping and one small dent on the outer rim (see photos).
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This one has paint chipping and top outside rim has a dent (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
This is a used collar for the 228F lantern.
Condition will vary.
This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).
Used 228 old style vent. Has some paint chippings, scratches/scuffs and color looks a little faded (see photos)
Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.
This product is not included in the OCP free shipping program.
Photo's with lanterns are for illustration purposes only.
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
Fount dated 5-77 for the model 220/228 Lanterns, models H thru K. This fount has some scratches, paint chipping, and rust - see photos.
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-65.
Has paint chipping and a couple scratches/scuffs (see photos)
Fount dated 12-80. For models 220/228 H thru K. Has some scuffs/scratches and paint chipping on the bottom of the fount (see photos).
This is a used burner frame that will fit models 228B through 228F.
Has a bit of rust
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
This is the decal used on the early painted 220D/228D transitional lantern.
This is a used old style fount for the 220/228B through 220/228F lanterns.
Has small scratches/scuffs, chips and looks like some plastic got melted to the outside but might be able to get it off (see photos).
Coleman Lantern Logo for 1955 to 1961 220 & 228 E Lanterns
Instruction Decal for 1945 to 1946 220C & 228C Lanterns. Also fits some 220D & 228D Lanterns
White Border Logo with "Reg.", "Pats. Pending" & "Lantern" for1965 to 1971 200A, 220 & 228 F Lanterns. Also fits the 220G,
Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns
No Border Logo with "Reg." & "Lantern" for 1961 to 1964 200A, 220 & 228 E & F Lanterns
White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.
Dark Red Border Logo with "Reg.", & "Lantern". For "Some" 1971 to 1983 200A, 220, 228, 335, 236A, 237A Lanterns. This and the D11 were used interchangeably on the same lanterns/stoves. Compare with your original.
Longer vent rod for models 220/228B through 220/228E and 235.
Used Smith-Victor carry case for all large hat 228 style lanterns. Will also fit 220, 252, 275, 290, and 295.
Has some scratches, one edge is bent a little but doesn't hinder the case closing, both latches aren't perfect on latches tight but is a little bent, the other latch is loose but still closes.
This product is not included in the OCP free shipping program.
Eccentric Block for the model 220/228H, 220/228J, 220K, and 206 lanterns.
Used Sears big hat ventilator. Will also work on the model 228 lantern. This has been painted before scratches/scuffs chipping paint and a tiny bit of rust - otherwise in good condition (see photos).Â
NOS Fuel and air tube for model 220 & 228 through B through K lanterns.
This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.
Valve stem for 220 / 228 B, BX, C, D, E and F.
Used valve stem nut for many Coleman lanterns.
Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.
Shorter vent rod for models 220/228F through 220K
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.
Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
New nickel plated brass burner caps with round head. Fits most models of double mantle lantern and lamps.
New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.
This is a lot of 10 used brass 220 size burner tubes and caps. The caps will all have screens. Most of the burner caps are steel but some are brass. All the burner tubes are brass. I created this product for the guys that like to build fish gigging lights. A low cost alternative to buying all new burner tubes and caps.
