Search
Valve Assembly - 290 - C018
This is a Coleman made new valve assembly that fits the 290 and 290A model lanterns. These have a metal eccentric block, feed tube, new knob and screw included.
Generator - 290/295 - C014
This is a new Coleman made generator for Model 290, 290A and 295 Lantern. Each includes new gas tip, spring, and cleaning needle.
This generator can be used on the 290 series lanterns, but you will have to use your original generator nut instead of the new one that comes with this generator. The 290 generators have been discontinued.
These are also known as part number 3000005404 and replaces the 290 & 290A part number of 290-5891.290 Collar Black, Used - X14
Used collar for the 290 lantern. Has a black circle around the center hole rather than red.
290 Collar Red, Used - X30
Used collar for the model 290-700 lantern. Has red around the center circle rather than black.
290/295 Heat Shield - C042
These fit all 290 and 295 model lanterns.
- The 290 was originally made with a full frame and did not come with a heat shield, so this version is a bit of work to get installed. Once in place, it ends up covering the lighting holes in the bottom of the frame - FYI.
- On a 290A and 295, you will need to replace the frame bottom also if yours has riveted in springs.290A Collar Red, Used - X36
Used collar for the model 290A700 lantern. Has red around the center circle rather than black.
- Free Shipping
286A-288A-290A Directions - E1656
Only 1 left in stockUsed directions for operating the 286A, 288A, and 290A Lanterns. See condition in the photos.
Generator Nut, Reproduction - S168
Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
288 Heat Shield, Used - E1009
Fits 285, 288, 290 and 295 model lanterns.
These are used and will vary in wear.
- New!
220 Peerless Globe - G130
This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
- New!
220 Red Logo Pyrex Globe USA - G129
This is a US made Pyrex replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Generator Nut Used - E1610
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Knob Assembly - C065
Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
Clamshell 220/228 Carry Case - CC5
Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.
This product is not included in the OCP free shipping program.
Photo's with lanterns are for illustration purposes only.
288 Knob, Used - E1399
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
Nut - E1028
Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.
- New!
220 Globe Sears Logo - G59
This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 Century Schott Suprax Globe - G50
This is a used Century Primus globe 8936 made by Schott Suprax Glas made in West Germany. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Has a spot that looks glued or burnt on (see photos)
Schrader Valve Core - R510
These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.Need more information on the valve core? Click HERE.
- Free Shipping
U Clip, Used - S96
Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns.
Will all vary in wear and some may have rust .
Same as part number 288-1251
621/635 Generator Needle - S15
Compatible with 635 and the 621 series lanterns. This is a reproduction part.
Reproduction Canadian Ball Nut 242 - R575
Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns.
- Free Shipping
O-Ring - S21
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
- The fuel tube on the 550B stove
- On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251
Feed Tube - 282/285/286/288 - C010
New feed tube assembly made by Coleman. Includes new Schrader valve and O-ring. Fits all 282, 285, 286, and 288 model lanterns.
Pump Screw, Reproduction - R504
Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.
- New!
242 Vent Rod, Reproduction - S145
Reproduction nickel plated vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.
- New!
Ball Nut, USA Style, Used - E1617
This is a used ball nut for the 247, 249, and 242 Lanterns - except it will not fit the 242 No Letter / Junior.
Bail Reproduction - R309
This is a very nice reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Made of spring steel here in the USA.
242 Bail Used - E1531
This is a used bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Will show wear and rust and such, but be solid.
- New!
242 Burner Frame, Used - BF504
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
Is stamped with 3000.
- New!
Ball Nut 242 Reproduction - R419
Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.
- New!
242 Burner Frame, Used - BF503
This is a used Burner frame for the 242A through C lantern. Will also work on the 247.
Is stamped with 3000.
- New!
Fount 242, 9-47, Used - F157
This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)
Burner Tube with Nut - Steel - E1127
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
Burner Tube, Brass, NOS - E1269
New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
Burner Tube Steel - E1357
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.
- New!
220 No Letter Globe - G179
Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
- New!
242 Burner Frame, Used - BF505
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
This one will need a new burner cap or screen.
Is marked with 3000.
Filler Cap Screw 242 Size - S66
New filler cap screw for the small 242 & 249 lanterns and 500 stove size filler caps.
Bail Reproduction Bent - B100
Reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Looks identical to the original.
These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.