1/4" Valve Stem Bushing - S137
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.
New 200 burner frame Pal Nut is HERE.
New 200 burner frame Nut is HERE.
This is a used fount for the model 200A lantern. Has some paint chipping, scratches/scuffs and two very small dents you can only see in certain lights (see photos). Otherwise in nice shape - inside of tank looks good too.
This is a used fount for the 200A lantern dated 6-76. This fount as a couple paint chipping/scuffs, overall great condition (see photos)
This is a used fount for the 200A lantern dated 9-60. Has some scratches/paint chipping and a dent by the pump assembly (see photos)
Used short style vent for 200/200A lanterns. This vent has some paint chipping (see photos)
Used short style vent for the 200/200A lanterns.
This vent has some scuffs/scratches and a little paint chipping (see photos).
Used short style vent for the 200/200A lanterns. Has a some scratches/scuffs and paint chips (see photos).
Used tall style vent for the 200/200A lanterns.
This one has some scratches and paint chipping (see photos)
This is a used tall style vent for the 200 and 200A Lantern.
Has some paint chips (see photos)
Used tall style vent for 200/200A lanterns made in 1962 and before. This vent is the slightly darker cherry red and is in great shape. This vent has paint chipping and has very tiny white dots all over it - color looks slightly faded (see photos)
Used tall style vent for 200/200A lanterns made in 1962 and before. This vent has some rust and chippings (see photos).Â
New, reproduction latch for the 200A and "some" of the 220 clamshell carry cases. Please make sure your case looks like the one in the photo - if it does, it will fit.
This is a used collar for the model 200A lantern.
It may show signs of wear/scratches. Each collar may slightly vary in wear.
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a few imperfections in the glass, color is faded and has one burn mark (see photos)
New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
Also known as part number R690B051.
These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
This is a used Pyrex old red letter logo replacement globe used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
New old stock Optimus Globe - Made in West Germany by Jenaer Suprax Glas. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 249 and other similar sized Lanterns.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a burn mark and one small spot missing the amber (see photos)
This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. Red globes are "Made in U.S.A." Very rare and hard to find.
This one has a manufacturer defect (shown in photos). The defect is just a distortion and came that way from the factory.
This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
This is a new old stock Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. Comes with the red trailblazer logo. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.
Used spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Reproduction valve stem for the model 200A lantern. Comes with a new valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.
New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.
Used short style vent for the 200/200A lanterns made in 1963 and after.
This vent has some scratches/scuffs and paint chippings (shown in photos)Â
Burner tube for the 201 kerosene lantern. Has a larger opening on the end than the 200 burner tube.
New old stock silk lite mantles. Much better than the new ones. 2 mantles in this unopened package.
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
New frosted sunrise logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
New half frosted globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
Used, black filler cap with lanyard - in good shape. Comes with new lanyard. Comes with a new gasket that you will have to install.
This is a used 242 Optimus Globe. It will fit models 200, 200A, 200B, 201, 202, 234, 242A, 242B, 242C, 243, 243A, 247 and 249.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
Looks like it may have gotten a little too hot and burned (see photos)
Generator Needle For Northstar Lantern 2000-750T 2000-750 2000-750E 2000A750. This is a reproduction part.
Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.