- Free Shipping
220 Burner Screen - S30
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
This is a used Century Primus globe 8936 made by Schott Suprax Glas made in West Germany. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Has a spot that looks glued or burnt on (see photos)
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
New frosted sunrise logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects.
The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"
This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.
New half frosted globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
Used metal parts safe for the 220/228 lantern. Great for storing extra mantles, generator, matches or anything else. These are used but function as intended.
Looks almost new - gasket still looks good!
This is an original used old stock amber globe. Some of these globes have the light blue band around the top and bottom of the globe as is common with the old ones. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Globe is stamped with "Made in U.S.A."
This one looks like it's had some good use - faded and a little dirty (see photo)
This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.
This is a US made replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
Used, black filler cap with lanyard - in good shape. Comes with new lanyard. Comes with a new gasket that you will have to install.
This is a used burner frame that will fit models 228B through 228F.
Has a bit of rust
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is a used vent. Has some paint chipping (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
This one has paint chipping and top outside rim has a dent (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping and one small dent on the outer rim (see photos).
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
This is a used burner assembly with the round mixing chamber that will fit the model 220F & 228F. It will be in fine working condition. It may show signs of tarnish and other spots from being old.
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Round steel burner cap for most models of double mantle lanterns and lamps.
Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
This is a lot of 10 used brass 220 size burner tubes and caps. The caps will all have screens. Most of the burner caps are steel but some are brass. All the burner tubes are brass. I created this product for the guys that like to build fish gigging lights. A low cost alternative to buying all new burner tubes and caps.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381