Pump Repair Kit, Neoprene - E1352
New old stock pump that fits most models except for the small Peak 1 lanterns and stoves.
Packaging might be a little beat up.
New old stock pump that fits most models except for the small Peak 1 lanterns and stoves.
Packaging might be a little beat up.
Burner Assembly. Fits electronic ignition model 5017 only.
NOS Burner Assembly. Fits Matchlight model 5017 only.
NOS steel original funnel for the model 252 Milspec lanterns and 530 stove.
Used clear quadrant glass pane for the milspec lantern. They are not perfect, on some of them edges are slightly chipped as was common on these. They measure approximately 3 3/8 inches wide and 5 1/4 inches high.
Used Military Lantern globe channel. Crimps on burner frame to hold quadrant globe panes. May show sings of rust and wear.
Older style fuel tube for stoves.
This is a used vent for models 220 and 228B through 228E. Has paint chipping and rust, pretty rough (see photos).
This is a used vent. It will fit models 220B through 220E.
Please see photos for condition
This is a used vent. It will fit models 228F through 228J. This vent has some paint chippings and rust (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is a used ventilator for the model 220B through 220E lantern.
Please see photos for condition
This is a used ventilator for the model 220B through 220E lantern.
This vent has some rust and paint chips (see photos)
This is a used vent for models 227 and 228B through 228E.
Please see photos for condition
This is a used vent for models 227 and 228B through 228E.
Please see photos for condition
Used 228 old style vent.
Please see photos for condition.
NOS ball nut for rare 062 globe holder. Will work on lamp models 131G, 131P, 131K, 141, 141A and may fit others.
NOS generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
Unknown NOS check valve. Measures 13/16"
Wick Assembly for Coleman Deluxe Catalytic Heater model No. 515B708
Boot is approx 1 3/16" wide and the wick is approx 1" wide.
Handle that fits many cooler models made by Coleman. It measures 5" wide.
Burner Assembly Left. Fits models 5430B and 5430C stoves.
Valve stem for the 201 Lantern
This is a snap on plastic tray made for the model 220/228 lantern. You would snap it on to the bottom of the tank to carry extra generators, mantles, matches, or whatever. It comes with a generator wrench, pump lube, and silk lite mantles. These have not been made in many years.
The package is very rough and dirty.
Used short style vent for 200/200A lanterns.
Has paint chipping and rust (see photos)
Burner tube for the model 5107 lantern.
Burner tube for the model 5120 and 5122 LP lantern.
This is a used fount for the 220/228K lantern.
Please see photos for condition.
It will work for any 220/228H through 220K type models.
If you would like us to install a new check valve in this fount before sending it to you, please make a note on the final check out page or send us an email to support@oldcolemanparts.com after clicking HERE and purchasing a new check valve. There is no cost for the service, just for the new part.
Used tall style vent for the 200/200A lanterns.
Please see photos for condition
Used Fount for models 220/228 Lanterns, models H thru K.
Please see photos for condition
If you would like us to install a new check valve in this fount before sending it to you, please make a note on the final check out page after clicking HERE and purchasing a new check valve. There is no cost for the service, just for the new part.
Used short style vent for the 200/200A lanterns.
Has one paint chip (see photos).
This is a used vent. It will fit models 228F through 228J. This vent has some slight paint chippings and scratches (see photos).
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is an original filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
NOS Valve Stem Complete for the model 502 stove.
NOS brass pre-heater cup for the model 249 lantern.
NOS Shorter vent rod for models 220/228F through 220K
New direction disk for the model 201 lantern and the 413H stove.
Valve Delay Kit for Models 9223 and 9230 undercounter furnace.