Lanterns
220F Vent, Small Frame - U883
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Sears Vent, Used - V118
Only 1 left in stockUsed Sears small hat ventilator. Will also work on the model 220 lantern. This one has some paint chipping and a dent (see photos)
- New!
Pre-Heater Cup USED - E1632
Used pre-heater cup. This is in good shape. 1-5/32" wide with a center hole measuring just over 1/4". Can be used with small generators.
220/228 Fount New Style Used - U893
This is a used fount for the 220/228K lantern dated 12-73. Has a few scratches/scuffs and rust around the bottom, but is otherwise in good shape.
It will work for any 220/228H through 220K type models.
Fount 288, Used - F174
Used fount for the model 288 or 286A lantern dated 7-93. Has some scuffs and slight rust around the bottom (see photos). It has no dents.
200A Valve Stem, Reproduction - S05
Reproduction valve stem for the model 200A lantern. Comes with a new valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Pump 242B Steel, Used - E1014
Used steel pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather. Has the double screw holes on the plunger cap.
- New!
228 Burner Frame, Old Style, Used - U923
Only 1 left in stockThis is a used burner frame that will fit models 228B through 228F.
Has a bit of rust
Filler Cap 3 Piece Yellow Used - E1040
This is for one used 3 piece yellow filler cap.
Comes with a new gasket that you will have to install.
Tip Cleaner Assy - E1183
This is a reproduction tip cleaner stem specifically for the #107 Leacock Kitchen Lamp. May fit other applications as well. It measures 2 1/8 inch long.
295 Fount, Used - F153
Used Unleaded Fount for the model 295 lantern. Has some scratches. It is dated 1-95.
- New!
222 Fuel Cap and Lanyard - E1158
Used filler cap with lanyard for the small backpacking lanterns - in very nice shape. Will also fit most other lantern and stoves that use the standard size filler cap. Comes with a new gasket that you will have to install.
290A Collar Red, Used - X36
Used collar for the model 290A700 lantern. Has red around the center circle rather than black.
290 Collar Black, Used - X14
Used collar for the 290 lantern. Has a black circle around the center hole rather than red.
335 Valve Assembly, Used - E1682
This is a used valve assembly for a Canadian model 335 lantern.
Valve stem packing has not been changed but one will be included for you to change if needed.
242 Pump Assembly, Used - E1589
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the single screw hole on the plunger cap.
Hollow Wire, NOS - E1556
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 3/16"
CQ Lamp Wrench, Used - E1368
Only 2 left in stockFrom Terry Marsh's site: This wrench came with a Coleman L220 lantern dated Aug. 1928. The instructions with the lantern identify this wrench as part no. 362-950. It is 4″ long and fits nut sizes 11/16, 7/16, & 2, 5/16″ plus a 5/32″ slotted generator tip remover. This wrench also came with iron Models 4A & 609.  Link is HERE.
228F Vent, Small Frame - U887
This is a used vent. It will fit models 228F through 228J. This one has paint chipping and top outside rim has a dent (see photos).
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
220F Vent, Small Frame - U880
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
- New!
Fount 220/228, New Style, Used - U895
Fount dated 12-80. For models 220/228 H thru K. Has some scuffs/scratches and paint chipping on the bottom of the fount (see photos).
Valve Assembly Early D Style, NOS - E1400
NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.
220 Lantern Reflector - LR3
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)
Milspec Tip Cleaning Tool, One sided - E1196
Generator tip cleaning tool for the military lantern - This tool is missing the pricker rod on one side of the tool.
- New!
220C Fuel Cap and Lanyard Used - Aluminum - E1178
Used, black filler cap with lanyard - in good shape. Comes with new lanyard. Comes with a new gasket that you will have to install.
Collar Assembly - X11
Collar assembly for the model 5107 and 5107A lantern. New old stock but has some scratches.
335 Fount, Used - F169
This is a used fount for the model 335 lantern. It is date stamped 1-77. It has surface scratches, but no dents. The inside looks excellent as it still has the reddish brown colored factory primer that is very visible.
130 & 131 Lamp Valve, NOS - E1176
Lamp valve for 130G, 130K 130P and 131P. The bottom is threaded for a fuel and air tube to be attached.
Regulator Valve Assembly, NOS - E1260
Valve for the 5154B, 5152D, and 5153A propane lanterns with electronic ignition. Comes with ignitor cam and knob/screw.