Lanterns
- Free Shipping
Check Valve Pip - S56
New rubber pip for the re-buildable NRV type check valve used on the 242, 242A, and the M1950 stove.
- Free Shipping
- Free Shipping
O-Ring - S21
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
- The fuel tube on the 550B stove
- On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251
Valve Assembly Used - U820
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
Fuel and Air Tube, NOS - E1630
NOS Fuel and air tube for model 220 & 228 through B through K lanterns.
Filler Cap Tire Valve Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Air Stem, Old Style, Used - S107
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
Bail Wrap Protector Black - R513
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Pump Screw, Used - S108
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Eccentric Block - E1039
New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.
252 Filler Cap Chain Bracket - R506
This is the small part that attaches to the filler cap screw so you can hook the chain to it.
Pump Cup & Nut, Neoprene - C008
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091Black Valve Wheel New Style, Used - S112
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
- Free Shipping
- Free Shipping
Tip Cleaning, Needle Tool - S131
Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.
Check Valve Milspec - R421
Reproduction check valve for the military lanterns. Will also fit the models 220/228B and 220/228C. Will not fit the later style lanterns.
- Free Shipping
Milspec Chain Ring - R500
This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.
Ball Nut 242 Reproduction - R419
Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.
Eccentric Block - S28
Eccentric Block for 200, 200A, All 242s, 201, 202, 243, 234, 335, 339 and 247. Also Sears 476.74550 & 476.72211.
288 Heat Shield - C032
Fits models 288, 288A and 288B lanterns. If you need it for a 288, it will fit down inside your frame, but it is some work to get in there. It will not cover the lighting holes.
The frame bottom is replaced if your current lantern has riveted in springs. This one will accommodate the updated spring configuration.- Free Shipping
O-Ring Single #9 - S22
O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone.
It is verified it will fit the 533 Stove - 2 are needed.
Tip Cleaner Stem Reproduction - R700
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3
Check Valve Old Style - R425
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
1/4" Valve Stem Bushing - S137
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
Small Pump Plunger - C035
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.
Filler Cap Insert 242 Size - S147
Filler cap insert for the models 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. Also fits the model 500 stove. Will have a new gasket installed.
327 Vent Bushing - R422
Reproduction vent bushing for the Air O Lantern, model 327, or 427 lantern. Will work on any older Coleman lantern that took a nickle plated brass vent. Now you can repair that old 2 piece vent and put it back together again correctly. Slightly peen over the ends of the new bushing to hold everything together.
Feed Tube Assembly - C058
Feed Tube Assembly for the 214 Lanterns.
Also known as part number 2145231ZCL.
Burner Tube, Brass, NOS - E1269
New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
Eccentric Block, Used - S117
Used Eccentric Block - these are not the plastic ones, but metal. Also known as part number 214-3041.
290/295 Heat Shield - C042
These fit all 290 and 295 model lanterns.
- The 290 was originally made with a full frame and did not come with a heat shield, so this version is a bit of work to get installed. Once in place, it ends up covering the lighting holes in the bottom of the frame - FYI.
- On a 290A and 295, you will need to replace the frame bottom also if yours has riveted in springs.Needle Assembly, Used - S99
Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.
Pre-Heater Cup - R318
Pre-heater cup for the model 237 lantern. This is a new production cup made out of brass. It is very high quality and fits the 237 nice and snug. Will also fit a 530 stove if you want to install a PH cup on it.
Burner Tube Brass 2 7/8 - E1254
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Valve Assembly Used - U821
Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.
Burner Cap Reproduction - S34
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
- New!
Valve Packing 275 - P04
This is special valve packing for the model 275 lantern. It is too big for other models. Has a 7/16 inch outside diameter and is 3/8 inches long.
- Free Shipping
Single Mantle Disk Reproduction - S01
New reproduction direction disk for the 200 & 200A USA lanterns. These are aluminum and look and feel identical to the original. These are made here in the USA. Will also fit most other lanterns. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantle" as opposed to "mantles" for a double mantle lantern.
Bail Reproduction - R309
This is a very nice reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Made of spring steel here in the USA.
Check Valve, Reproduction - S143
Reproduction check valve for 242, 242A, 242K, 243 and 243A lanterns. This is the re-buildable type check valve for early single mantle lanterns that did not use an air stem. Will not work with others.
Generator Nut - E1262
Original NOS generator nut for the Milspec lantern. Military part number 6260-00-161-1859
Metal Funnel Small - R503
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
220/228 Valve Bushing Set - S134
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
Bail Handle Reproduction - R308
This is a very nice reproduction bail handle for the model 236 and 237 lanterns. Made of spring steel here in the USA.