Lanterns

Reproduction check valve for 242, 242A, 242K, 243 and 243A lanterns. This is the re-buildable type check valve for early single mantle lanterns that did not use an air stem. Will not work with others.

Original NOS generator nut for the Milspec lantern. Military part number 6260-00-161-1859

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.

This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.

This is a very nice reproduction bail handle for the model 236 and 237 lanterns. Made of spring steel here in the USA.

Used Direction disk for the single mantle 200A lantern.

Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.

New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.

Coleman Decal For Canadian Made 1954, 200 Lantern

Vent rod for the Quick-Lite lanterns. It is 1 1/4 inches long.

These came out of the old SMP factory. This is the washer that goes behind the pump nut on an SMP military lantern.

Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.

Solid brass with stainless steel screen.

Same part number as 112-323

Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.

Brand new pump For the Northstar Lantern. 

Fits models 2000-750T, 2000-750, 2000-750E, and 2000A750.

Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.

Reproduction filler cap insert for the older winged style filler caps used on model 427 lanterns. Comes with the new gasket.

Shorter vent rod for models 220/228F through 220K

Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111

Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.

Includes:

• 4 Coleman string tie mantles for the 200 or 200A lantern
• 1 Reproduction Generator for the 200 or 200A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 200 HERE
• 200A HERE

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

This is a Coleman made new valve assembly that fits the 290 and 290A model lanterns. These have a metal eccentric block, feed tube, new knob and screw included.

Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

Check valve for the Northstar lantern.

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is a very nice reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns. Made of spring steel here in the USA.

This is a used collar for the 220F lantern.

This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8

This has been reported to be the correct size to repair the valve on the 400B and the 533A stoves. One is needed for both.

Decal for Kamplite lanterns

Used Gas tip.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

This is a used collar for the model 200A lantern. 

It may show signs of wear/scratches. Each collar may slightly vary in wear.

Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.

Used generator spring for 200, 200A, 242, 243, 202 & Similar Sears Lanterns. This is the older style.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.

Used direction disk for the 220/228H lantern. Will show signs of wear but still be in good condition.

Brass burner tube for the models 236 and 237.

Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.

This will fit all 286 model lanterns.

New reproduction direction disk for the many of the 2 mantle lanterns made in the USA like the 220 and 228 models B thru F. These are aluminum and look and feel identical to the original, and they are made here in the USA. They come with a protective plastic coating that can be removed before installation.

This disc refers to "mantles" as opposed to "mantle" for a single mantle lantern.

Eccentric Block for the model 220/228H, 220/228J, 220K, and 206 lanterns.

This is a 10 PACK of the cardboard tube that goes inside of the 200A and 220 size generators, and many others.

This is a used newer style U tube with Venturi. These are used.

Reproduction generator needle for the model 236 lantern.

Reproduction vent rod for the model 236 and 237 lantern. Made of solid brass.