Lanterns

Generator tip cleaning tool for the military lantern.

Burner tube for the model 339 lantern.

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Used Burner assembly for the model 200A lantern. 

Used direction disk for the later double mantle lanterns such as 220/228, J-K. Will show signs of wear but still be in good condition. 

Amish style filler plug for the early Quick-Lite lanterns and lamps. Does not use an air stem and requires a hand pump.

New old stock valve assembly for the QuickLite model 327 lantern.

Used Bail Handle

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

Unknown used ball nut. Kind of like half a ball nut.

New Old Stock eccentric block for the 285, 286, 288 and 290 lanterns. These are made of metal and will not melt like the original plastic ones. Also known as part number 288C3041.

This is a used bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Will show wear and rust and such, but be solid.

This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #6

Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.

Tip cleaning needle for 201, 241 and 247 Kerosene lantern generators. New reproduction part.

Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is a used burner frame for the model 200A lantern. 

Used wing nut for the milspec lantern.

New valve body for the model 335 lantern. Will show tarnish from age.

Reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.

These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #9.

Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.

Reproduction gas tip for the model IL 323 lantern generator.

Burner Assembly for the model 288 lanterns. The burner tubes are steel. Will vary in wear.

Valve stem for 220 / 228 B, BX, C, D, E and F.

Propane Tee for connection of 2 appliances to a refillable propane tank. 

Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.

Includes:

• 4 Peerless mantles for your lantern
• 1 Reproduction generator
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

This is a used burner frame for the model 200A lantern.

Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

This is a used old style burner frame originally used on the black band 200A Lantern. Looks like someone may have replaced the tabs - they are supposed to be short.

New Old Stock parts. Comes with original box.

New old stock base bracket for the military lantern.

This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)

This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

Bail for the Northstar propane lantern. 

This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7

It has been reported that the 285 valve stem uses 2 of these.

Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.

This is a used collar for the model 242B lantern. It may have spots of rust or other discoloration/ stains.

Valve Complete for the 5107 and 5107A propane Lantern

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Vinyl adhesive-backed for hobby projects.1.5" tall x 7.25" long.  Stick it on your project, paint, then remove.

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8.

Knob

Steel burner tube for the 214 lantern.

Used Bulk Adapter

Fits 275 lantern.

Filler cap lanyard for the small backpacking lanterns. 

This is a used tall style vent for the 200 and 200A Lantern. 

Has some paint chips (see photos)

Used tall style vent for the 200/200A lanterns.

This one has some scratches and paint chipping (see photos)