Lanterns

Filler cap lanyard for the small backpacking lanterns. 

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Vinyl adhesive-backed for hobby projects.1.5" tall x 7.25" long.  Stick it on your project, paint, then remove.

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8.

Knob

Steel burner tube for the 214 lantern.

Used burner assembly for the old model 327,427, also for CQ and Air O Lite lanterns. Will also work on other lamps that would have originally taken the Q99 generator.

Used Bulk Adapter

Fits 275 lantern.

Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.

They will all show varying signs of wear.

This is a used tall style vent for the 200 and 200A Lantern. 

Has some paint chips (see photos)

Used tall style vent for the 200/200A lanterns.

This one has some scratches and paint chipping (see photos)

Used Canadian 242B collar with small writing.

Each will vary in amount of wear and discoloration.

Used tall style vent for 200/200A lanterns made in 1962 and before. This vent has some rust and chippings (see photos). 

Cam Follower

This kit is for the 550 stove specifically. It includes 4 O-rings.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

Used collar for the model 286A or 288A lantern. Marked for both models.

Used collar for the model 288A lantern.

Used short style vent for 200/200A lanterns. This vent has some paint chipping (see photos)

This is a used ventilator for the model 220B through 220E lantern. 

This vent has a few paint chippings. (see photos)

This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.

This one will need a new burner cap or screen.

Is marked with 3000.

Fits 275A lantern.

This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-65. 

Has paint chipping and a couple scratches/scuffs (see photos)

This is a used fount for the 200A lantern dated 9-60. Has some scratches/paint chipping and a dent by the pump assembly (see photos)

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

This is a used ball nut for the 247, 249, and 242 Lanterns - except it will not fit the 242 No Letter / Junior.

Reproduction globe clamps made to work with the 062 shade. Only work with that one style.

Parts kit for the model 5151A propane lantern. Includes heat shield, vent bracket, 2 gaskets and nut.

Used bail handle for the model 5107 lanterns

This is a used collar for the 335 lantern.

This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.

This is a reproduction bail handle for the model 236 and 237 lanterns.

They are new but a little rusty and warped/bent - they can be fixed with a little patience and a propane torch.

Used short style vent for the 200/200A lanterns. 

This vent has some scuffs/scratches and a little paint chipping (see photos). 

This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

This is a used fount for the model 200A lantern. Has some paint chipping, scratches/scuffs and two very small dents you can only see in certain lights (see photos). Otherwise in nice shape - inside of tank looks good too.

Used tall style vent for 200/200A lanterns made in 1962 and before. This vent is the slightly darker cherry red and is in great shape. This vent has paint chipping and has very tiny white dots all over it - color looks slightly faded (see photos)

Used burner assembly for the model 295 lantern.

Used burner frame that will fit models 220B through early 220F through approximately 1971.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns. 

Is stamped with 3000.

This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

This is a used old style fount for the 220/228B through 220/228F lanterns. 

Has small scratches/scuffs, chips and looks like some plastic got melted to the outside but might be able to get it off (see photos).

Reproduction valve stem for the model 238B lantern.

This is a used ventilator for the model 220B through 220E lantern. 

Has some paint chips and scratches (see photos)

This is a used collar for the early 288 lantern. Has the black circle around the opening rather than the red.

Rec Vehicle Adaptor

Fits model 275 lantern.

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7.

It has been reported that the 285 valve stem uses 2 of these.