Lanterns

O ring.

Collar and bolt for the model 635 and 639 lanterns.

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.

Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.

This is a used collar for the model 327, 427, and similar lanterns. Some will have some surface rust - all will vary with wear.

Valve stem that I can't identify. Has a pointed end. It is 1 3/4 inches long. Has a smaller diameter shaft that would take the small packing. The valve stem nut is for a 7/16 wrench. Has a solid formed wheel that is not held on with a screw.

Used Air flow restrictor cap for the model 159X lamp.

Air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247. 

Is stamped with 3000.

N.O.S Valve stem for the model 335 and 339 lanterns.

Has a small chip on the valve wheel.

Air Intake Tube for the model 275 Lantern

Bulk adaptor

This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below. 

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

Used valve stem for Quick-Lite lanterns.

These have not been serviced or cleaned and may need a new P02 packing which is HERE.

Used burner assembly for the model 275 series lanterns.

Used collar for the model 286A lantern.

Used collar for the model 285 lantern.

Frame bolt. Fits the 5107C, 5114C, 5151, 5152. May fit others.

Fits 214 and 286 model lanterns.

Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.

This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.  

Comes with a new gasket for you to installed if needed.

This is a used fount for the 200A lantern dated 6-76. This fount as a couple paint chipping/scuffs, overall great condition (see photos)

Used valve body for the slant lanterns and lamps.

Lamp valve.

Mixing chamber for lamps and lanterns. It has the burner tube holes at a wider spacing than the normal mixing chambers. The burner tube holes are 1/1/2 inches apart center to center. Normal mixing chambers are spaced 1 3/8.

Used collar for the model 295 lantern.

Unknown Coleman direction disk. I do not know what it goes to. It is a small disk with only an 11/16 inch diameter.

Generator Extension

Burner frame assembly for the model 5152A lantern.

This is a used collar for the model 321B lantern.

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 1/8"

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 1/8"

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

New valve stem packing has been installed.

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

New burner assembly for the model 286 lantern. The burner tube is brass. 

This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.

Used closed ball nut.

Fount dated 5-77 for the model 220/228 Lanterns, models H thru K. This fount has some scratches, paint chipping, and rust - see photos.

This is a used collar for the model 242C lantern. All will vary with wear and discoloration.

Stud for 321 and  Peak 1 lanterns

This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

Used short style vent for the 200/200A lanterns made in 1963 and after.

This vent has some scratches/scuffs and paint chippings (shown in photos) 

Used fount for the model 288 lantern. Dated 5/88. Slight rust and chipping. No dents.

Used collar for the CL1 lantern.

Aluminum mixing chamber for most double mantle lanterns and lamps. Coleman experimented with aluminum for a few parts back in the old days. I believe it was discovered that aluminum could not hold up to the heat. Probably more of a display piece than for using.

This is a used vent for a Quick-Lite Lantern model 227, 327, and 427.

Has a couple dents and nickel plating has worn off - all brass (see photos)

Used burner frame for the models 228H and 228J lanterns.

Pack nut for the model 275 lantern.