Lanterns

Used frame plate for the model 220/228 H and J lanterns. Has been cleaned but may show signs of light wear. 

For model 220 -228J lanterns

Vent nut for the Northstar lantern.

Vent rod for the Quick-Lite lanterns. It is 1 1/4 inches long.

Vent rod for the model 5114 propane lantern.

Reproduction vent rod for the model 236 and 237 lantern. Made of solid brass.

Shorter vent rod for models 220/228F through 220K

Longer vent rod for models 220/228B through 220/228E and 235.

Used Vent bracket. 

Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern. 

Vent bracket. 

Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern. 

Used vent for the model 275 and 275A. Has two chips - shown in photos.

This is a used ventilator for the model 220B through 220E lantern. This vent has paint chips (see photos)

This is a used vent. It will fit models 220B through 220E. 

Has paint chippings and a small bulge towards by the ball nut opening (see photos)

Used valve wheel screw.  Will be in good condition.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.

This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.

This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.

This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.

Valve stem for 220 / 228 B, BX, C, D, E and F.

New NOS valve stem for the model 200A lantern.

Valve stem for Quick-Lite lanterns.

These have not been serviced or cleaned and may need a new P02 packing which is HERE.

Used valve stem for the model 220/228H, J, and K lanterns. Has been cleaned and will have new graphite packing.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.

Used valve stem nut for many Coleman lanterns.

Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.

N.O.S Valve stem for the model 335 and 339 lanterns.

Has a small chip on the valve wheel.

NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

Valve stem for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

Reproduction valve stem for the model 238B lantern.

Used valve stem for the model 200A lantern. Has been cleaned, and packing changed.

Used valve stem for Quick-Lite lanterns.

These have not been serviced or cleaned and may need a new P02 packing which is HERE.

Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.

This is special valve packing for the model 275 lantern. It is too big for other models. Has a 7/16 inch outside diameter, 1/4" inside diameter and is 3/8 inches long.

Others have said this also fits some older Coleman stoves like the 9D. 

T shirt shaped piece for the valve on slant lanterns and lamps.

New valve body for the model 335 lantern. Will show tarnish from age.

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

Valve stem packing has not been changed but one will be included for you to change if needed.

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

New valve stem packing has been installed.

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.

This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.

New old stock valve assembly for the QuickLite model 327 lantern.

This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced. 

NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.

New valve assembly for the model 335 lantern.

Valve assembly for 639 Kero lantern.

Valve assembly for Northstar Lantern.

Valve Assembly for the 285 lantern.