Other Brands

Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point.

A fellow collector has shared with us that it will also fit the Akron 107 with a built on pump.

O rings for the Thermos lantern and stove pumps. One is for the pump, the other is for the top seal. These are for the later model Thermos lanterns and stoves where the pump and filler cap where combined.

Filler cap gasket for the Prentiss Waber lantern.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.

Cap gasket for Akron lanterns. Outside diameter is 5/8 of an inch. Inside diameter is 3/8 of an inch. Thickness is 1/8 inch.

This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.

This also fits the AGM 2572 & Kamplite RL-3 

Pointed Bottom Sears Lantern Replacement Decal

Rectangle Later Sears Lantern Replacement Decal

Decal for the Thermos lantern. It is approximately 2 1/2 inches long and is 1 1/4 inches high at the widest point. The background silver is too sparkly on these. Reduced price to sell.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Reproduction generator for the AGM model LRL21, LRL21A, LRL22, KL2, and JC Higgins model 710.7400, 710.74001 lanterns. Part number on JC Higgins parts diagram is 7110 - Generator Assembly

Decal for Kamplite lanterns

Ted Williams replacement decal for Sears Ted Williams lanterns

Decal for the Thermos "Holiday" lantern.

Reproduction generator for the Sunshine Safety lanterns and lamps. Similar to the Coleman Q99 but has a different nut. Will not work on Coleman lanterns and lamps.

This is a sealer similar to Gasoila - for sealing valves to tanks.

Screen retainer. Has an approximate diameter of 7/8 of an inch.

Eccentric block for AGM lanterns. Measures 15/16 of an inch long.

Burner cap. Similar in size to the Coleman 220 burner cap.

Gas tip for Thermos stoves.

Decal for Montgomery Ward Hawthorne lantern.

Decal for the AGM model 3016 Lantern. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Burner screw for Thermos stoves.

Fuel needle. Measures 3 7/8 inches long.

Reproduction control knob disc for red Sears lanterns models.

Burner ring for Thermos stoves. May show signs of light rust.

Pump. Measures 5 3/4 inches long.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

Unknown screen. Measures 1/2 inch in diameter. Very fine brass. Seems too fine to be for a burner screen. Came out of a lot of old AGM parts.

Generator for Akron iron.

Fuel tube and screen for Thermos stoves. It is 3 inches long.

Burner cap with 5 holes for thermos lanterns.

Fuel tube. Measures 2 1/2 inches long.

Valve stem for thermos stoves.

This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.

Burner cap with 3 holes for Thermos lanterns.

This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.

Fuel tube. Measures 3 1/8 inches long.

Gas tip hood for Thermos stoves.

Thermos generator for models 8489, 8490, 8491 stoves. New generator includes new gas tip, spring, and tip cleaning wire.

This horizontally striped frosted globe is approximately 3 7/8 inches tall and has a 4 3/8 inch diameter.

Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

I believe these generators are for an AGM iron. They measure 4 inches long.

These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.

This is a used collar for a model 476.74070 Sears lantern. Wear will vary.

This is a used collar for a model 476.74060 Sears lantern. Wear will vary.

Decal for the Punker Alcohol Stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.