Other Brands

Used Sears fount dated 3-66. 

It's in pretty good shape just has some scuffs and minor scratches. 

This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:

Decal for the Preway Model P4521 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4522 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Term-Sport Alcohol Stove Tank Decal. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

I believe these are burner tubes for an AGM double mantle lantern. They are 2 7/8 inches long. Roughly the same diameter as Coleman burner tubes. Made of steel.

The Canadian 990 globe was made to fit the model 331 lantern. Does not fit any other gas lantern model. Very rare globe to find these days. Will also fit the Thermos lantern models 8311 and 8312.

Top cap for the Leacock lamp handle.

Came in a box marked Primus parts. Looks like the outer housing for a pump. Measures 7 3/4 inches long.

New old stock generator for the Aladdin PL1 lantern.

Needle assembly for Thermos stoves. Measures 11 inches. New old stock but is very rusty.

This is a used collar for a model 476.72213 Sears lantern. Wear will vary.

Decal for the Preway Model P4821 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4521-A stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Valve body for Thermos stoves.

Thermos generator for inverted lantern models 8319 and 8321. Also fits Kamplite and JC Higgins inverted lanterns. May show signs of tarnish but is new old stock. New generator includes new gas tip, spring, BUT DOES NOT HAVE a tip cleaning wire.

Decal for the Preway Model P4523 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Term-Sport Alcohol Stove Burner Instruction Sheet. Reproduction.

Don't know the part number for this valve and generator. It measures 10 1/4 inches long from tip to end of nut. 

Fuel tube and screen for Thermos products. It is 3 7/8 inches long.

This is a used vent.  Has chipping and a little rust as shown in photos.

Fuel tube and screen for Thermos stoves. It is 2 1/2 inches long.

T- Block

Decal for the Preway Stove models 209, 312 & 318. Label is peel and stick. Made of paper like original.

Decal for the Preway Model P4822 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4823 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.

Generator for some model of AGM lantern. Measures only 1 9/16 inches long.

Unknown valve stem. Has a tag on it that says it is part number 4-4005. Measures about 3 1/2 inches long.

Fuel tube and screen for Thermos appliances. It is 2 5/8 inches long.

Drain cap for the KampKold cooler.

New old stock stove tank for the 3 burner Thermos stove models 8431 and 8432.

#20 Wick for Kerogas oil cook stove

Thermos stove valve stem with orange valve wheel.

Generator for some model of AGM lantern. Measures only 1 9/16 inches long. Missing the tip cleaning needle.

This is a used bail handle for a non Coleman made lantern. It is approximately 5-3/4" inches wide is approximately  5-3/4" inches high.

Don't know what this came from. It is about 4 7/8" long, the smallest end is about 3/4" wide and the biggest end is about 7/8" wide. From wing to wing it is about 2 1/2" wide.

Used Vent for Ash Flash lantern model 1010

Used Solus filler cap