Other Brands

Generator for an AGM lantern. Measures 1 1/2 inch long.

Generator for an AGM lantern. Measures 3 9/16 inches long.

Generator for AGM lanterns. Measures 3 1/8 inches long. Fits the AGM model 3025 lantern. Thanks to Joe P. for this information.

Globe nuts for the Thermos and Kamplite inverted lanterns.

Thermos generator for models 8325 and 8326. May show signs of tarnish but is new old stock. New generator includes new gas tip, spring, and tip cleaning wire.

Thermos generator for models 8311 and 8312. May show signs of tarnish but is new old stock. New generator includes new gas tip, spring, and tip cleaning wire.

Thermos stove generator for models 8422, 8425, 8426, 8427, 8428, 8429, and 8432. New generator includes new gas tip, spring, and tip cleaning wire.

Used Sears fount dated 8-68 . Has paint chipping/scratches, no dents.

Burner cap with 5 holes for thermos lanterns.

Burner cap with 3 holes for Thermos lanterns.

Used Vent for Ash Flash lantern model 1010

This is a used vent.  Has chipping and a little rust as shown in photos.

This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.

The Canadian 990 globe was made to fit the model 331 lantern. Does not fit any other gas lantern model. Very rare globe to find these days. Will also fit the Thermos lantern models 8311 and 8312.

Generator for some model of AGM lantern. Measures only 1 9/16 inches long. Missing the tip cleaning needle.

Decal for the Preway Model P4521 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Generator for some model of AGM lantern. Measures only 1 9/16 inches long.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

This is a used bail handle for a non Coleman made lantern. It is approximately 5-3/4" inches wide is approximately  5-3/4" inches high.

Decal for the Punker Alcohol Stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Thermos lantern. It is approximately 2 1/2 inches long and is 1 1/4 inches high at the widest point. The background silver is too sparkly on these. Reduced price to sell.

New old stock generator for the Aladdin PL1 lantern.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is a used collar for a model 476.74070 Sears lantern. Wear will vary.

This is a used collar for a model 476.74060 Sears lantern. Wear will vary.

These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.

This is a used collar for a model 476.72213 Sears lantern. Wear will vary.

Don't know what this came from. It is about 4 7/8" long, the smallest end is about 3/4" wide and the biggest end is about 7/8" wide. From wing to wing it is about 2 1/2" wide.

Burner cap. Similar in size to the Coleman 220 burner cap.

Thermos generator for models 8489, 8490, 8491 stoves. New generator includes new gas tip, spring, and tip cleaning wire.

This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.

This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:

This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Reproduction control knob disc for red Sears lanterns models.

This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.

This also fits the AGM 2572 & Kamplite RL-3 

Reproduction generator for the Sunshine Safety lanterns and lamps. Similar to the Coleman Q99 but has a different nut. Will not work on Coleman lanterns and lamps.

Don't know what this one fits. It could be for a lantern or small stove. The gen body is 4 3/16 inches long. The tip cleaner rod extends out another 5/8.

Don't know the part number for this valve and generator. It measures 10 1/4 inches long from tip to end of nut.