Other Brands

These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.

Gas tip for Thermos stoves.

Burner screw for Thermos stoves.

Drain cap for the KampKold cooler.

Unknown screen. Measures 1/2 inch in diameter. Very fine brass. Seems too fine to be for a burner screen. Came out of a lot of old AGM parts.

This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Screen retainer. Has an approximate diameter of 7/8 of an inch.

This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:

Needle assembly for Thermos stoves. Measures 11 inches. New old stock but is very rusty.

Case latch wire for Thermos stoves. Kind of a light blue color. It is 1 inch tall and 1 inch wide.

I believe these are burner tubes for an AGM double mantle lantern. They are 2 7/8 inches long. Roughly the same diameter as Coleman burner tubes. Made of steel.

Screw set for Primus. Screws are 7/8 of an inch long.

Top cap for the Leacock lamp handle.

Fuel needle. Measures 3 7/8 inches long.

Fuel tube and screen for Thermos stoves. It is 3 inches long.

Fuel tube and screen for Thermos appliances. It is 2 5/8 inches long.

Slightly smaller than a Coleman pump clip.

Burner ring measures 2 7/8 inches diameter.

Collar for the Thermos model 8325.

Filler cap gasket for the Prentiss Waber lantern.

Came in a box marked Primus parts. Looks like the outer housing for a pump. Measures 7 3/4 inches long.

Used collar for a Hawthorne model 60-9521 lantern.

Used collar for a Hawthorne model 60-9536 lantern.

Unknown collar for a non Coleman lantern. Measures about 1 7/8 inches tall and has a diameter of 3 1/16 inches.

Collar for the Thermos lantern.

Cap gasket for Akron lanterns. Outside diameter is 5/8 of an inch. Inside diameter is 3/8 of an inch. Thickness is 1/8 inch.

Decal for the Thermos lantern. It is approximately 2 1/2 inches long and is 1 1/4 inches high at the widest point. The background silver is too sparkly on these. Reduced price to sell.

Decal for Kamplite lanterns

Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point.

A fellow collector has shared with us that it will also fit the Akron 107 with a built on pump.

Decal for the Preway Stove models 209, 312 & 318. Label is peel and stick. Made of paper like original.

Decal for the Preway Stove models 408, 409 & 412. Label is peel and stick. Made of paper like original.

Eccentric block for AGM lanterns. Measures 15/16 of an inch long.

Gas tip hood for Thermos stoves.

Used pump for the Sunflame Speedikook model 6906 stove.

Fuel tube and screen for Thermos stoves. It is 2 1/2 inches long.

Fuel tube and screen for Thermos products. It is 3 7/8 inches long.

Term-Sport Alcohol Stove Burner Instruction Sheet. Reproduction.

Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4823 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4822 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4523-A stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4522-A stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4521-A stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4523 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway Model P4522 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.