Stoves

Valve minus the generator for the model 425 series stoves.

1/4 inch long screw for the 500 stove. Used on the baffle, see description tab for more details. Two are required for the 500 stove.

Parts tube for the M1941, M1942, 520 and 523 military stoves. Each contains a new vaporizer, gas tip, large packing, and 3 screens. LINK for great info on these and what they fit.

Valve assembly Fits 508A, 508B, 533 and the 533A

This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

Wind baffle support.

Leg for the M1950 military stove.

Reproduction generator needle for the model 500 and for the 345 kerosene marine stove.

Valve and Generator. Fits the model 413H and 426E stove.

Regulator, clip on. If you want the threaded on one it would be 9942A-5251.

This is a complete rebuild kit for the pump on an M1942 stove. You will get the cap gasket, check valve dot, and pump leather.

Stainless steel diffuser plate for the model 530 stove. 4 inch diameter. Professionally cut.

Rebuild kit for 502 Sportster Stove. Cures most troubles.

Includes:

• 1 Reproduction Generator for the 502 stove lanterns
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in Below

More parts for the 502 Stove HERE. 

Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.

Fits multiple models of small backpack stoves

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Fuel Air Tube for the 413 series and 442 series 2 burner stoves. NOS.

Used Valve Regulator Assembly.

Filler cap gasket for the model 523 military stove.

N.O.S feed tube assembly. Fits 502 Stove. 

Large leather pump cup for the T-Handle pumps, kitchen ranges, and other larger appliances. The flat portion of the cup measures 1" wide. For pump barrels with a 1 1/4 inch diameter.

Stainless Steel grate screw for model 502 stove. Uses a total of three.

Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.

NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit.  No other sizes of chain are currently available that are an exact match to what was used.

Tip cleaner needle for inside the vaporizer on a model 520 stove. NOS - will show some surface rust here and there from sitting on a shelf for many years.

This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

Military wrench for the model 520 stove. Stamped US. These have some corrosion on them that you can see in the picture.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Air stem for the 530 stove.

NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.

Needle & Holder

Used valve Stem for the 425 F and G  stove only, will not fit earlier models. Measurements:  just over 1-3/4" long and 1/4" diameter. You will also need a P01 graphite packing for this HERE.

This has the 1/4" diameter width, not the smaller 3/16". The 425F came with both the 3/16" and the 1/4". The model 425F was a transition year, so be sure to measure your current valve stem is 1/4".

This is a used pump square nut.

Comes with one square nut ONLY.

This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.

Wrench for the military model 520 stove. New old stock. These are not stamped US and they do not have the little clip on the opposite side.

This is the spring used in the non return valve located in the bottom of the M1942 pump. Reproduction part.

Solid brass nut for the model 345, 348, 500, & 502 stoves. Possibly used in other applications also. Refer to the parts diagram of your model if unsure.

Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.

This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.

Valve stem for the 425, 425B,C and E stoves

Regulator Assembly

Fuel and Air Tube for many stoves. Same as part number 425-6461.
Fits 2G, 2H, 4F, 6B, 6F, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 417B, 425 models, 500, &500A.

Pot support leg for the model 520 stove. New old stock but they show signs of rust.

Parts tube for 520 and 523 military stoves. Contains a new vaporizer, gas tip, large packing, and 3 screens. The outer tube has a minor rust spot or two. The parts inside are fine. LINK for great info on these and what they fit.

Fuel Tube

Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.

Generator Coil. Rusty. 

Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.

Used pump for the model 530 stove. Will have a new pump leather and work just fine.

Original reproduction wrench for the model 536 or M1950 stove.