Stoves

Vinyl adhesive-backed for hobby projects.1.5" tall x 7.25" long.  Stick it on your project, paint, then remove.

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8.

This is a new old stock pre-heater valve for the M2 military stove.

Air stem - long pump rod for stoves. Measures 10 1/2 inches long.

Needle.

Used Bulk Adapter

Used burner support for the 502 stove. Will have varying rust on each one but all are solid.

Used collar for the 502 stove. Will vary in wear, but will still be in good condition.

Burner Assembly Left

Block and needle

Gas tip

Made by Coleman - this is the part that connects the round ball tank to the regulator.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

This is a reproduction knob for the Coleman made M1950 stove. The color of these match the original Coleman made color. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.

This is a reproduction knob for the Rogers made M1950 stove. The color of these match the original Rogers darker color. We have found the earlier stoves (made around 1953) were darker than the newer ones (made around 1963). The last photo shows the difference in color between the two. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.

Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.

P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).

This is a used handle for many Coleman stoves. Please verify yours is silver in color, measures 5 13/16" long and looks like these - there were some made that were thinner and painted green. These will not fit without modification on those. These will show signs of rust and wear.

Gas tip

Gas tip.

Found on the earlier than 425F stove models. Use part 412-2531 to make a complete valve assembly.

Used direction disk for the model 530 stove.

This is a new manifold assembly that fits the 413H and 414 stoves only. 

Valve for stove model 445-700 and 445-700C

Large filler cap for kitchen ranges and other large appliances. New old stock but has a new gasket installed.

Vinyl adhesive-backed stencil for Model 9C stove. Stick it on your tank, paint, then remove.

Vinyl adhesive-backed stencil for Model 2 stove. Stick it on your tank, paint, then remove.

Pump Plunger. Fits the Peak 1 Apex Stoves 450-700, 445-700, 445-700C

Valve Comp

Rec Vehicle Adaptor

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7.

It has been reported that the 285 valve stem uses 2 of these.

Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.

Valve wheel for Handy Gas Plant.

Lighting lever for stove

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.

Used burner fillers and cap for the model 502 stove. Has some rust but seems to be in good shape.

Bulk adaptor

Used 530 valve with vaporizer

Used burner bowl for the 502 stove. Rusty, but seems solid. Each one will vary with the amount of rust.

Burner assembly for the rare 414 gas stove with electronic ignition.

Valve body assembly that fits 5410A700, 5410A708, and 5410B708

Gas Tip Assembly

HYAK diverter for Coleman 3 burner stoves.

Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

NOS black knob. Same knob as part number 5445-1491 only a different color.

Unknown ceramic material type of burner button used on some heaters and stoves. This has a diameter of 3/4 and is 3/4 tall.

Used direction disk for some propane stoves. Small disk with little less than a 3/4 inch diameter.

Valve for the small military 527 stove.

Reproduction eccentric block for the model 527 stove.

Manifold pipe. It is 8 5/16 inches long.

Needle for the 740 stove generator.