Stoves

This is a used pip holder cup for the M1950 stove pump. Comes with a new rubber pip.

This is a cap for the end of the M1950 pump. This screws into the bottom of the pump.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Vinyl adhesive-backed stencil for Model 9C stove. Stick it on your tank, paint, then remove.

Vinyl adhesive-backed stencil for Model 2 stove. Stick it on your tank, paint, then remove.

Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Valve stem for the 425, 425B,C and E stoves

NOS valve minus the generator and valve wheel, for the model 425 series stoves. 

Grate hinge for the 348 stove box. 

Used top half of a 530 stove - Comes with burner supports.

Used top half of a 530 stove. Missing all of burner supports.

One used wind baffle support in good working shape.

Valve minus the generator for the model 425 series stoves.

Bracket screw for the model 500 and 500A stove - Screw ONLY.

If you need just the bracket it is HERE.

Bracket for the model 500 and 500A stove - Bracket ONLY

If you need just the screw it is HERE.

Reproduction generator needle for the model 500 and for the 345 kerosene marine stove.

Regulator Assembly

Fits multiple models of small backpack stoves

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.

Also known as part number 3000005094.

NOS Generator Coil. 

Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.

Propane Tee for connection of 2 appliances to a refillable propane tank. 

This is a used stove grate for the model 425B stove.

New, 8 foot reinforced high pressure hose.

This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.

Generator coil. Measures 7 1/4 inches long and the width is 7/32". Made of steel.

Used collar for the model 500A stove.

NOS Generator Coil for models 425s, 415C, 415D, 416 B. 416C, 2G, 9G, 2H, 9H, 2B, 9A, 9B, 417B, 4F, 6F. 6B, 412B, 421, 421D, 391 and 391A. 

NOS, HGP cap. Fits models 457, 457G, 575, 460, 470G Handy Gas Plants. Also fits the 465 Tank. 

This is a used stove grate for the 502 Coleman stove. It will show signs of being used.

Needle And Rod for the 396, 396A, 396B and 397 cabin stoves.

NOS Valve for tanks 457, 465, and 653D.

Valve stem only. Fits the 413E, 413F, 413G, 413H, 425F, 426E, 442, 442A, Sears Models 476.72303, 476.74980, 476.72302, and 476.74970. Comes with a new packing installed. Also known as part number 413A2521.

Stem (lighter) assembly. This was the last style used on the 500B Canadian Stove, will also work on the 500 and 500A. This is a rare part.

Valve Assembly for the model 502 stove without fuel pickup tube. 

Reproduction wrench for the 530 pocket stove.

Generator Coil. Rusty. 

Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.

Strainer gasket.

Used Fuel Valve Assembly

Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves

Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.

Needle & Holder

Used Valve Regulator Assembly.

Used burner bowl for the 502 stove. These are in good shape and may have some rust. The photo is an example, not the actual.

This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.

Looks like it may have gotten a little too hot and burned (see photos)

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.