Stoves

Bracket screw for the model 500 and 500A stove - Screw ONLY.

If you need just the bracket it is HERE.

Small nut for bottom of stove grate.

Original used grate screw for model 502 stove. Each stove uses a total of three.

O ring made of gas resistant Viton. Outer diameter 7/16". Works on many propane stove models such as 5400A.

Two required for the model 550 stove.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Fuel and Air Tube

Fuel Air Tube for the 413 series and 442 series 2 burner stoves. NOS.

Stainless Steel grate screw for model 502 stove. Uses a total of three.

Phillips head screw.

Leg for the M1950 military stove.

1/2 inch long screw for the 500 stove. Requires two for the Cap and Fillers. See description tab for more details.

1/4 inch long screw for the 500 stove. Used on the baffle, see description tab for more details. Two are required for the 500 stove.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

This is the gasket that goes on the 5400-5211 valve stem. It is a small flat washer. Known to fit models 5410A700, but may fit others.

This does not work on the 5430A700 or the 5430B700.

Fuel tube gasket for the model M1950 military stove.

Pump check valve pip for M1942 stove.

Used direction disk for some propane stoves. Small disk with little less than a 3/4 inch diameter.

Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Filler cap gasket for the model 523 military stove.

This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Cap Gasket for M1942 & M1950 stoves.

This is a screw for 242 pumps where the top of the pump fits inside the fount and for other applications with this thread.

NOS Direction disk. Small disk with little less than a 3/4 inch diameter. Mostly used on propane stoves - will be way too small for a GPA lantern or stove.

This is a used stove handle for many stoves. 

It measures 5 13/16 inches across. Will show signs of rust and wear.

It is know for sure to fit the 413E and a 425C. 

One used wind baffle support in good working shape.

Burner support screw for a 502 stove. Each stove requires 3 total.

Screw/Bolt for the burners on 5435A and 5435B Stoves. 2 are needed for both stoves.

O-Ring

This is a used pump square nut.

Comes with one square nut ONLY.

Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.

Hose Adaptor

This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

Used Nut

Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.

NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit.  No other sizes of chain are currently available that are an exact match to what was used.

This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.

This fits many applications for propane appliances.

Gas tip.

HYAK diverter for Coleman 3 burner stoves.

Generator Coil. Rusty. 

Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.

Brass flat head screws

Used legs for the 520 military stove.

NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.

This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #9.

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8.

This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7.

It has been reported that the 285 valve stem uses 2 of these.

This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #6

Strainer gasket.

NOS Generator Coil for models 425s, 415C, 415D, 416 B. 416C, 2G, 9G, 2H, 9H, 2B, 9A, 9B, 417B, 4F, 6F. 6B, 412B, 421, 421D, 391 and 391A.