Stoves

Bracket screw for the model 500 and 500A stove - Screw ONLY.

If you need just the bracket it is HERE.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

Grate hinge for the 348 stove box. 

4 Screws W/Washer Stainless For 530

This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..

This is a screw for 242 pumps where the top of the pump fits inside the fount and for other applications with this thread.

Reproduction generator needle for the model 500 and for the 345 kerosene marine stove.

Reproduction generator nut for the 500 and 500A stove.

Solid brass nut for the model 345, 348, 500, & 502 stoves. Possibly used in other applications also. Refer to the parts diagram of your model if unsure.

Small nut for bottom of stove grate.

Stainless Steel grate screw for model 502 stove. Uses a total of three.

This is a used stove grate for the 502 Coleman stove. It will show signs of being used.

Valve Assembly for the model 502 stove without fuel pickup tube. 

This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.

This fits many applications for propane appliances.

Used legs for the 520 military stove.

Parts tube for 520 and 523 military stoves. Contains a new vaporizer, gas tip, large packing, and 3 screens. The outer tube has a minor rust spot or two. The parts inside are fine. LINK for great info on these and what they fit.

Pot support leg for the model 520 stove. New old stock but they show signs of rust.

Tip cleaner needle for inside the vaporizer on a model 520 stove. NOS - will show some surface rust here and there from sitting on a shelf for many years.

Wrench for the military model 520 stove. New old stock. These are not stamped US and they do not have the little clip on the opposite side.

Military wrench for the model 520 stove. Stamped US. These have some corrosion on them that you can see in the picture.

Parts tube for the M1941, M1942, 520 and 523 military stoves. Each contains a new vaporizer, gas tip, large packing, and 3 screens. LINK for great info on these and what they fit.

Filler cap gasket for the model 523 military stove.

Valve for the small military 527 stove.

This is a reproduction flame diffuser plate for the 520 and 530 stoves. These are very nice plates. Professionally cut. 4 inch diameter.

Stainless steel diffuser plate for the model 530 stove. 4 inch diameter. Professionally cut.

Used direction disk for the model 530 stove.

Used pump for the model 530 stove. Will have a new pump leather and work just fine.

Eccentric block for the model 530 stove.

Used top half of a 530 stove - Comes with burner supports.

Used top half of a 530 stove. Missing all of burner supports.

Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.

Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.

Looks like it may have gotten a little too hot and burned (see photos)

Used 530 valve with vaporizer

Reproduction wrench for the 530 pocket stove.

This is the gasket only from the 5423A5611 small parts kit. OD 1/2", ID 3/16", Thickness is just under 1/16" Was commonly used on the model 5413, 5413A, 5423, 5430B, 5433, 5430B, 5430C, 5435C, 5435D and similar propane stoves.

New, 8 foot reinforced high pressure hose.

Air stem - long pump rod for stoves. Measures 10 1/2 inches long.

Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".

This is a reproduction air stem for the large filler caps as used on Handy Gas Plants, Radiant Heater #2, Remote Tank 457 and 465, and other large tanks.

Air stem for the 530 stove.

Auxiliary valve. Fits 417B, 4F, 6F, 6B, and 412B Stoves.

Auxiliary Burner Bowl, Rings And Screw 413E/413F/413G/424/426B/426/D/426G/442/442A/443  Instant Light, 2 & 3 Burner Stoves

Block and Needle Assembly. Measures approximately 4 1/4 inches long.

Block and needle

Bulk adaptor

Used Bulk Adapter

Used bunsen for the 502 stove. Will have varying signs of wear.

Burner for the model 522 military stove.

Burner assembly for the rare 414 gas stove with electronic ignition.

Burner Assembly Left