Stoves

One used wind baffle support in good working shape.

Wind baffle support.

Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.

This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.

This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.

This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.

Used valve Stem for the 425 F and G  stove only, will not fit earlier models. Measurements:  just over 1-3/4" long and 1/4" diameter. You will also need a P01 graphite packing for this HERE.

This has the 1/4" diameter width, not the smaller 3/16". The 425F came with both the 3/16" and the 1/4". The model 425F was a transition year, so be sure to measure your current valve stem is 1/4".

Valve stem only. Fits the 413E, 413F, 413G, 413H, 425F, 426E, 442, 442A, Sears Models 476.72303, 476.74980, 476.72302, and 476.74970. Comes with a new packing installed. Also known as part number 413A2521.

Valve stem only. Fits the 413E, 413F, 413G, 413H, 425F, 426E, 442, 442A, Sears Models 476.72303, 476.74980, 476.72302, and 476.74970. Comes with a new packing installed. Also known as part number 413A2521.

This is the gasket that goes on the 5400-5211 valve stem. It is a small flat washer. Known to fit models 5410A700, but may fit others.

This does not work on the 5430A700 or the 5430B700.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

These are new old stock and have a bit of rust on them from sitting on a shelf for decades. Comes with a packing from the factory. Fits stoves 3F, 3H, 413B, 413C, 413D, 418, 418B, 419, 420, 371, 371A. Does not come with the needle.  If your stove has been updated to a later valve style then this would not fit.

The needle and holder for this is part number 471-2381 HERE.

A whole new valve and gen would be part number 413B6601.  That is the valve that fits the 413E and 413G stoves.

Valve stem complete for stove 393 396, 396LC, 396A, 396A-LC, and 397

Valve stem for the 425, 425B,C and E stoves

Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.

NOS valve stem for many of the older Coleman stoves. Compare your diagram with the part number 412-253 to verify it will fit. Will not fit into the 414, 424, 425, 426 series stoves.

Valve stem complete less needle for Generator 950-262

Valve stem

Valve stem for 890 series kitchen range type stoves.

Used Valve Regulator Assembly.

Regulator Assembly Fits the 445A, 450A and 3021 Stoves

NOS valve minus the generator and valve wheel, for the model 425 series stoves. 

Valve minus the generator for the model 425 series stoves.

NOS Valve for tanks 457, 465, and 653D.

Valve body assembly that fits 5410A700, 5410A708, and 5410B708

Valve Body

Found on the earlier than 425F stove models. Use part 412-2531 to make a complete valve assembly.

Valve Comp

Used valve assembly for the model 502 stove. Valve stem packing has not been changed but one will be included for you to change if needed.

Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.

P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).

Valve assembly

Valve assembly Fits 508A, 508B, 533 and the 533A

Valve assembly for the 400B, 3024, 442  and 440 single burner stoves.

Valve and hose for the 9720 stove.

Valve and generator.

Valve and Generator. Fits the model 413H and 426E stove.

Valve and Generator. Used on model 424.

New Coleman made valve and generator. This part will fit: 2G, 2H, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 421, 421C, 421D, 421E, 425, 425B, 425C, 425D, 425E, 425F and Sears 476.72301, 476.74960, and 476.72244.

Valve and generator for stoves 393, 396, 396LC, 396A, 396A-LC, and 397.

Control Valve & Generator Assembly Complete 414/428

New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980

Valve for stove model 445-700 and 445-700C

These are Used and have a bit of rust on them. Fits stoves 3F, 3H, 413B, 413C, 413D, 418, 418B, 419, 420, 371, 371A. Does not come with the needle.  If your stove has been updated to a later valve style then this would not fit.

The needle and holder for this is part number 471-2381 HERE.

A whole new valve and gen would be part number 413B6601.  That is the valve that fits the 413E and 413G stoves.

This is a used pump square nut.

Comes with one square nut ONLY.

Used Pump Assembly Spring

Spring ONLY

Don't know the part number for this valve and generator. It measures 10 1/4 inches long from tip to end of nut.