200A

Reproduction filler cap gasket for Coleman 3-piece fuel caps. Fits most Coleman lanterns and stoves that use the standard 3-piece cap with the center bolt. Good fit & quality replacement that helps stop fuel leaks. Red cap shown for reference only.

Look HERE for how to install these.

Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Peerless 2C-HG mantles, 4 per pack (M01). These are the most popular size mantles for many Coleman lanterns and lamps. Same size as Coleman 21A mantles and fit models including 200, 200A, 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5100 series, 5150 series, 9950, 9960 and most other Coleman pressure lanterns. Treated with thorium at the factory for bright white light. Known for being more durable and rugged than standard mantles. Made in India. Burn off outdoors first due to smoke.

Installation instructions are HERE if needed.

Reproduction filler cap gasket for Coleman one-piece fuel caps. Fits many Coleman lanterns and stoves that use the 1-piece filler cap without a center bolt or screw. Good quality replacement that helps stop fuel leaks. If your cap looks like the one in the photo, this is the right gasket. 

Look HERE for how to install these. Green cap shown for illustration only and is not included.

Also known as part number 425A1361

Reproduction generator tube packing for Coleman lanterns. This is the small tube that fits inside the generator on models 200A, 202, 220, 228, 242, 275, 288 and may fit others. Good quality replacement that helps keep your lantern running cleanly and reliably.

Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Full Box of 50 packs (2 mantles per pack).

These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

This decal is the correct replacement for a wide range of Coleman equipment manufactured between 1971 and 1983. It fits Lantern models 200A, 220, 228, 335, 236A, and 237A, as well as the 502 Sportster stove.

Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.

This is the "White Border Logo" decal featuring the "Reg.", "Pats. Pending", and "Lantern" text. It is the correct replacement for models 200A, 220F, and 228F manufactured between 1965 and 1971, and is also the appropriate fit for the 220G model.

Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.

Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.

Also known as part number 425A1405.

This replacement screen will fit the burner caps used on 200, 200A, 201, 242, and 243 lanterns.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.

Also known as part number 3000005094.

This is the "No Border Logo" decal featuring the "Reg." and "Lantern" text. It is the correct fitment for models 200A, 220, and 228E and some F Models manufactured between 1961 and 1964.

Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

New Coleman-manufactured burner cap designed for lantern models 200, 200A, 202, 243, 242, and 247. This part is also compatible with several lamp models and Sears lanterns.

Also known as part number 2423231.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345 or 2217976

New Coleman-manufactured pump assembly designed for most lanterns and stoves. This assembly includes a neoprene pump cup and features interchangeable parts to match your specific existing setup. Note: This assembly is not compatible with small Peak 1 type products, which utilize a shorter pump rod.

Also known as part number 242J5201.

This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. Also fits the 530 Pocket Stove. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

Yellow Border Logo Used on Coleman 200A Lanterns from 1954 to 1960. Includes the "Reg." text.

Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.

New 200 burner frame Pal Nut is HERE.

New 200 burner frame Nut is HERE.

New Coleman-manufactured 2-pack of ball nuts. This is the common size used on the majority of Coleman lanterns.

Also known as part number 3000005384.

Yellow Border Logo Used on Coleman 200A Lanterns from 1952 to 1953.

Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.

Coleman Lantern Logo Fits the 1951 model 200A and the 220 & 228E models manufactured from 1951 through 1954.

Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.

Used generator nut for many Coleman models. These are in fine shape, just dirty.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 234, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.

Also known as part number 242-353.

Used, round headed valve wheel screw.  Will be in good condition. These fit many models. Over the years, they changed the types of screws to hold on valve wheels. Please compare how this looks to yours if ordering. These will not fit the 236 or 237. 

Pump Clip

10-pack of reproduction filler cap gaskets for Coleman 3-piece fuel caps (S41). Ideal for many Coleman lanterns and stoves using the standard size cap with center bolt. Smart way to keep spares on hand and keep your gear leak-free. Red cap shown for reference only.

Look HERE for installation instructions.

Yellow Border Logo Specifically for the 1961 model 200A lanterns.

Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.

New steel fuel pick-up tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".

Also known as part number 200-1481

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This is a reproduction stainless steel burner frame for the model 202. It will also work on all models  200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.

New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. Top and bottom outer diameter is 3.25" and height is 4.25"

Also known as part number R690B051.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

Reproduction needle assembly for the 200A2891 T66 generator used on lantern and lamp models 121, 200, 200A, 202, 242, 242B, 242C, 243, 476.72211 & 476.74550.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style. 

In the 426 stove series, this only fits 426 or 426A

This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

New Coleman-manufactured neoprene pump cup with a large push-on nut. This versatile part fits nearly all Coleman stoves and lanterns.

Also known as part number 6391091.

These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.