200
-
200A Globe Old Red Logo - G71
This is an used original old red letter logo globe used on lanterns from 1960 to 1980. Although used it will be in good condition. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
-
Single Mantle Disk Reproduction - S30
New reproduction direction disk for the 200 & 200A USA lanterns. These are aluminum and look and feel identical to the original. These are made here in the USA. Will also fit most other lanterns. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantle" as opposed to "mantles" for a double mantle lantern.
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
Generator Tube Packing - P05
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Mantle String Tie #21 2 pack - M03
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Mantle String Tie #21 4 Pack - M02
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Peerless Mantles 2C-HG - M01
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
1/4" Valve Stem Bushing - S134
Small bushing for the tip of the valve stem. This is the small beveled bushing that goes on the valve stem below the graphite packing. This is the only bushing for these lanterns unlike the 220/228 that has a second one. Also fits the 202, 242, and 243 lanterns, along with many stoves with a 1/4" valve shaft.
-
Burner Frame Stainless - R500
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200 and 200A.
-
200A Reproduction Burner Frame - R308
This is a new reproduction frame for burner frame for the model 200, 200A, 201 and 202. It has the shorter bail tabs.
-
200A Fuel Tube Reproduction - R304
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
-
Burner Cap New - C09
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
-
-
Air Stem Used Old Style - S31
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
-
Check Valve With Stem - C01
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part. The latest part number for this is 2006381ZCL.
-
200A Collar Used - X13
This is a used collar for the model 200A lantern.
It may show signs of wear/scratches. Each collar may slightly vary in wear.
-
U Tube Newer Style With Venturi Used - E1486
This is a used newer style U tube with Venturi. These are used.
-
-
-
New Filler Cap Brass - C04
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Has gone in the past by part numbers 220C1401, and now 425A1405
-
Valve Wheel Screw - S72
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.
-
Reproduction Gas Tip - GT2
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
-
-
-
-
-
Neoprene Pump Cup And Nut - C08
Brand new Neoprene Pump Cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
-
Decal - Fits 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns - D11
White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.
-
Filler Cap Green Used - E1248
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear.
Comes with a new gasket.
-
-
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
-
-
Peerless Mantles 24-A - M04
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
-
Needle Assembly Reproduction - S62
Reproduction needle assembly for the 200A2891 T66 generator used on models 121, 200, 200A, 202, 242, 242B, 242C, 476.72211, 476.74550
-
Burner Screen - S89
This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.
-
Pump Assembly Leather Used Square Nut - E1256
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
Parts Safe Gasket 200A - E1253
This is a new gasket for your metal snap on parts safe. Fits the 200A size metal safe. Measures 5 1/4" from outside edge to outside edge of gasket.
-
Pal Nut - S16
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
-
Filler Cap 3 Piece Green Used - E1265
This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket NOT installed.
-
Valve Wheel Black Old Style Used - S79
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
-
Black Valve Wheel New Style USED - S78
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
-
Ball Nut Used - S18
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
-
-
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401