200A
-
200A Globe Old Red Logo G71
This is an used original old red letter logo globe used on lanterns from 1960 to 1980. Although used it will be in good condition. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
-
200A Globe Clear - G1
This is a brand new clear globe that will fit models 200, 200A, 200B, 201, 202, 242A, 242B, 242C, 243, 243A, 234, 247, 249, 5101, 5120, 5121 and 5122.
Top and bottom opening is 3-1/2", bulge width is 4-1/2" and is 4-1/16" tall.
Has also been reported to fit Austromax “Aussie Bush Light” very well.
-
Single Mantle Disk Reproduction - S30
New reproduction direction disk for the 200 & 200A USA lanterns. These are aluminum and look and feel identical to the original. These are made here in the USA. Will also fit most other lanterns. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantle" as opposed to "mantles" for a double mantle lantern.
-
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Mantle String Tie #21 2 pack - M3
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.Â
Typically used to stop a fuel leak from the valve stem on older appliances.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part numberc 118B6201 and 118D6201.Â
-
Mantle String Tie #21 4 Pack - M2
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Peerless Mantles 2C-HG - M1
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
Leather Pump Cup And Back-Up Plate - C6
Leather pump cup, push on nut and back-up plate. New part number 3000005094.
-
Generator Tube Packing - P5
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
-
200A Valve Bushing - S134
Small bushing for the model 200A lantern. This is the small beveled bushing that goes on the valve stem below the graphite packing. This is the only bushing for these lanterns unlike the 220/228 that has a second one. Also fits the 202, 242, and 243 lanterns.
-
Burner Frame Stainless - R209
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200 and 200A.
-
200A Reproduction Burner Frame - R216
This is a new reproduction frame for burner frame for the model 200, 200A, 201 and 202. It has the shorter bail tabs.
-
Tip Cleaner Stem Reproduction - S198
Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247 and similar lanterns.
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
200A Fuel Tube Reproduction - R211
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
-
Decal - Fits 1952 & 1953 200A Lanterns - D16
Yellow Border Logo Used on Coleman 200A Lanterns 1952 - 1953
-
Decal - Fits 1951 200A & 1951 thru 1954 220 & 228E Lanterns - D17
Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns
-
Decal - Fits 1954 to 1960 200A Lanterns - D14
Yellow Border Logo Used on Coleman 200A Lanterns 1954 to 1960 "Reg."
-
-
Decal - Fits 1962 to 1964 200A, 220 & 228 E & F Lanterns - D13
No Border Logo with "Reg." & "Lantern" for 1962 to 1964 200A, 220 & 228 E & F Lanterns
-
Decal - Fits 1965 to 1971 200A, 220 & 228 F Lanterns - D12
White Border Logo with "Reg.", "Pats. Pending" & "Lantern" for1965 to 1971 200A, 220 & 228 F Lanterns
-
200A Vent Bracket Short Reproduction - R213
Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.
-
200A Vent Bracket Tall Reproduction - R219
New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.
-
Bail Handle Reproduction - R224
Reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.
-
Fount Used 200A 5-53
This is a used fount for the 200A lantern dated 5-53. Has some chipped/cracked paint, no dents, seems solid.
-
Window Decal Lantern - Flat Black - D104
Window decal for glass or a hard surface - flat black in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Lantern Red - D102
Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part number 242-6201.
Made of 100% graphite.
-
-
Air Stem Used Old Style - S31
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
-
Check Valve With Stem - C1
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 check valve then this would be the correct part.
-
-
New Filler Cap Brass - C4
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.Â
Has gone in the past by part numbers 220C1401, and now 425A1405
-
Valve Wheel Screw - S72
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.
-
Push On Nut Small - S4
Push on nut for end of pump rod. The small push on nut is used with leather pump cups.
-
-
-
-
-
Neoprene Pump Cup And Nut - C11
Brand new Neoprene Pump Cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
-
Decal - Fits 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns - D11
White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns - Also fits 502 stove.
-
Filler Cap 3 Piece Red Used - E310
This cap will fit most models of lanterns. It is a used cap and will have some missing paint with the brass showing through in places. Has a new cap gasket installed.
-
-
-
Valve Wheel Red Old Style Used - S77
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
-
Filler Cap Tire Valve Nickel - R218
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.