200A

This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

Used valve wheel screw.  Will be in good condition.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.

Used cardboard tube that goes inside of the 200A and 220 size generators, and many others. 

Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a screw in the center then these gaskets will work. 

Red 3 piece filler cap show for demonstration purposes only.

This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. 

If your filler cap has a screw in the center of it then this gasket will not work. 

The red filler cap is shown for illustration purposes only and is not included.

Used spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.

This is a used pump square nut.

Comes with one square nut ONLY.

Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.

New 200 burner frame Pal Nut is HERE.

New 200 burner frame Nut is HERE.

Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

NOS metal pump cap for pump assembly

Does not come with whole assembly

This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.

Reproduction spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.

This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.

Eccentric Block

Used gas tip for 200A5891 generator. Also works well for using on the 220 generators when doing a kerosene conversion.

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

New Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

Pump Clip

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

Steel lock nut for the 200A lantern.

Used Pump Assembly Spring

Spring ONLY

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Yellow Border Logo Used on Coleman 200A Lanterns 1952 - 1953

Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns

Yellow Border Logo Used on Coleman 200A Lanterns 1954 to 1960 "Reg."

Fits 1961 200A Lanterns - Yellow Border Logo

No Border Logo with "Reg." & "Lantern" for 1961  to 1964 200A, 220 & 228 E & F Lanterns

White Border Logo with "Reg.", "Pats. Pending" & "Lantern" for1965  to 1971 200A, 220 & 228 F Lanterns. Also fits the 220G, 

White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.

Pump Cup Neoprene for most lanterns

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Fuel tube spring for lanterns with a fuel and air tube. Not used on lamps.

Small bushing for the tip of the valve stem. This is the small beveled bushing that goes on the valve stem below the graphite packing. This is the only bushing for these lanterns unlike the 220/228 that has a second one. Also fits the 202, 242, and 243 lanterns, along with many stoves with a 1/4" valve shaft.

200A Burner Tube

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

Valve stem nut for the model 214, 242 and 200 series lanterns.

Quick Clip mantles. Same size as Coleman 21A mantles.

This is a new gasket for your metal snap on parts safe. Fits the 200A size metal safe. Measures 5 1/4" from outside edge to outside edge of gasket.

Brand new Neoprene Pump Cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.

Zippo brand Flints for the Coleman Lantern Spark Igniter.

Used Direction disk for the single mantle 200A lantern.

Lock Nut for the 200A lantern. Goes on the top end of the burner tube.