200B

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. If your filler cap has a screw in the center of it then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part. Also known as part number 2006381ZCL.

This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004344.

New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

Also known as part number 425A1405.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Leather pump cup, push on nut and back-up plate. 

Also known as part number 3000005094.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

Pump Cup Neoprene for most lanterns

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Ball Nut 2 Pack.

Also known as part number 3000005384.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Pump Clip

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Heat shield clip for older style heat shields and for the 200B, 214, 282, 285, 290 and 295. Also works well as a pre-heater cup clip on kerosene lanterns.

Brand new Neoprene Pump Cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.

Also known as part number 6391091

Used bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.

This is a new gasket for your metal snap on parts safe. Fits the 200A size metal safe. Measures 5 1/4" from outside edge to outside edge of gasket.

This is a used USA made red letter replacement logo globe. Although used, it will be in good condition. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.

This is a very nice reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns. Made of spring steel here in the USA.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

This will fit all 286 model lanterns.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

Also known as part number R690B051.

Fits 282, 286, 200B lanterns

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.

Zippo brand Flints for the Coleman Lantern Spark Igniter.

These are used leather pump cups that fit most lanterns and stoves. They may need some oil and conditioning, but are still flexible. This is the typical sized 7/8" pump cups for most lanterns and stoves.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

Used cardboard tube that goes inside of the 200A and 220 size generators, and many others. 

New Filter Funnel For Lamps And Stoves. 

Stops filling your lantern or stove at the correct level.