201
-
Generator Lantern - C20
New Generator for 201 and 247 Kerosene Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
-
200A Globe Clear - G1
This is a brand new clear globe that will fit models 200, 200A, 200B, 201, 202, 242A, 242B, 242C, 243, 243A, 234, 247, 249, 5101, 5120, 5121 and 5122.
Top and bottom opening is 3-1/2", bulge width is 4-1/2" and is 4-1/16" tall.
Has also been reported to fit Austromax “Aussie Bush Light” very well.
-
Mantle String Tie #21 2 pack - M3
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Mantle String Tie #21 4 Pack - M2
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Peerless Mantles 2C-HG - M1
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
Peerless Mantles 24-A - M4
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part number 242-6201.
Made of 100% graphite.
-
-
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
-
-
-
Bail Handle Reproduction - R224
Reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.
-
Pal Nut - S16
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
-
Pump Clip Used - S17
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
Graphite Ribbon - P9
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
-
200A Vent Bracket Tall Reproduction - R219
New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.
-
Generator Tube Packing - P5
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
-
200A Reproduction Burner Frame - R216
This is a new reproduction frame for burner frame for the model 200, 200A, 201 and 202. It has the shorter bail tabs.
-
Valve Wheel Red Canadian Style Used - E558
Used valve wheel. Has the raised portion on the back side of the wheel as was found on some Canadian models. It is solid but does not have the small brass insert on the inside.
-
Tip Cleaner Stem Reproduction - S198
Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247 and similar lanterns.
-
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
New Filler Cap Brass - C4
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Has gone in the past by part numbers 220C1401, and now 425A1405
-
Valve Wheel Screw - S72
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.
Typically used to stop a fuel leak from the valve stem on older appliances.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part numberc 118B6201 and 118D6201.
-
-
-
Valve Wheel Black Square Hole Used - E76
Used valve wheel for 201, early 220B's and some model 237's. In the 426 stove series, this only fits 426 or 426A It fits on valve stems with a square shaft end. It is not interchangeable with other wheels.
-
200A Vent Bracket Short Reproduction - R213
Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.
-
Filler Cap Tire Valve Nickel - R218
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Brass - R236
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
-
Filler Cap Red Chipped - E91
Used filler cap that fits most Coleman lanterns and stoves. Paint is chipped with a few wrench marks.
-
Burner Frame Used #2 - E978
This is a used burner frame for the model 200A lanterns. Has rust as shown, no broken welds, decent shape.
This frame has the long ears or long tabs that hold the bail in place. Comes with setup for a tall vent, not the short style. Includes venturi tube, burner tube and cap with a good screen. -
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
Used Generator Nut - S26
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
-
Decal - Fits 201 Lanterns - Red Kerosene - D38
The decal maker made a mistake on this run. Rather than the word kerosene being in black like it should be, he made it red. Kind of a cool decal for a custom lantern.
-
Pre-Heater cup Small - C76
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter. The center hole is larger than needed for the 201 generator. Fits the 214 generator much better.
-
Push On Nut Large - S1
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
-
Burner Tube 201 - S175
Burner tube for the 201 kerosene lantern. Has a larger opening on the end than the 200 burner tube.
-
-
Valve Wheel Black Hollow Used - E556
Hollow style valve wheel. I believe these were used on some years of Canadian lanterns. Sold one at a time. Two wheels shown for illustration purposes only.
-
Filler Cap 3 Piece Used Copper Color - E729
This is a used 3 piece filler cap made of brass. Paint is worn and has a new filler cap gasket. Copper in color. Has wrench marks.
-
Filler Cap Red Used - E835
This is a used one piece filler cap. Paint is chipped or missing. Has a new gasket.
-
-
Pump Assy Leather Used Push On Nut - E965
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
Burner Cap Reproduction - S94
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.