206

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part. The latest part number for this is 2006381ZCL.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

Leather pump cup, push on nut and back-up plate. New part number 3000005094.

New Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

Ball Nut 2 Pack.

New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

Has gone in the past by part numbers 220C1401, and now 425A1405

New old stock nickel plated one piece cap. The ones I have left do not come in a package. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

Eccentric Block for the model 220/228H, 220/228J, 220K, and 206 lanterns.

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

Pump Clip

Generator nut. Fits many models of lanterns which take the 220E5891 generator: 220s, 228's, 275. Also fits many other models. Find your parts diagram HERE and verify the generator nut is listed as 605-210. 

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear.

Comes with a new gasket.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Kerosene fuel tube for the 206 and 231 model lanterns

These Peerless mantles are the same size as Coleman #11 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This is an original used globe made between 1936 to 1945 for Coleman lanterns that used the 220 size globe. Although used, it has been inspected for damage or defects (this one has a small bubble shown in picture) Please note that the green straight line logo used on these globes was very lightly stamped and can sometimes be difficult to see. This was normal for the time period. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket NOT installed.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

Used filler cap that fits most Coleman lanterns and stoves. Light gray in color like the early production Duel Fuel models. Paint is chipped or missing - each one will vary in wear. 

Comes with a new gasket - not installed

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.

USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.