220 Slant

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.

It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole. 

Old part number 115-1361. 

This will not seal they typical Coleman lantern cap.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

Fits models Air O lantern, 327, 427, Slant 220 lanterns and CQ lamps

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.

Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

Reproduction generator for the AGM model LRL21, LRL21A, LRL22, KL2, and JC Higgins model 710.7400, 710.74001 lanterns. Part number on JC Higgins parts diagram is 7110 - Generator Assembly

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.

Solid brass with stainless steel screen.

Same part number as 112-323

German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.

Universal pump assembly with leather cup that fits almost all Coleman lanterns and stoves. Does not fit the small Peak 1 lanterns or stoves, some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

T shirt shaped piece for the valve on slant lanterns and lamps.

This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.

USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.

This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.

Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves. Has a 7/8 inch diameter and is made of oiled leather.

This is a replacement amber globe. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Globe is stamped with "Made in U.S.A." 

This is a used scalloped edge winged filler cap that was used on the model 427 and other Quick-Lite lanterns with the pump that was mounted to the fount. It will show signs of nickel loss and some light wrench marks - will vary in wear. Comes with a new gasket installed. 

This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

This is a used pump assembly for the model 220b.  It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick. Has a nickel plated brass cap.

New old stock long pump for the model 220B and 220C lantern. These have a brass cap that connects the pump to the lantern. They have new pump leather on them. Probably made in the 1930's or early 40's.

This is a US made replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

This is a NOS pump assembly for the Canadian model 220B. It would also be correct for the 427 and 228B Canadian lanterns. The Canadian pump differs from the US in having a splined screw on cap rather than a checkered style.

This is a used winged filler cap that was used on the slant generator lanterns. Some models this was used on are: L220, 220B, 235, 4M, 2E,2F, 9E, AND 9F. 

Comes with a new gasket installed.

This is a reproduction mica globe for the model 327 lantern. It is new but was damaged in transport. 

It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations. 

This is a US made replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Has a burn mark  (see photos)