220BX
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
-
Peerless Mantles 2C-HG - M01
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
-
Generator for 220/228/275 - C002
New Coleman made generator for 220, 228, 275, and similar Sears lanterns. The new generator includes new gas tip, spring, and tip cleaning wire.
Will fit Coleman Lanterns: 220 B thru 220 J, 228 B thru J, 275 & 275A
Fits Coleman Lamp Models 117A, 118A, 118B, 119A, 132A, 133, 143 and 150
Fits Sears Lantern models 476.74060, 476.72212, 476.72213 and 476.74070This is the same generator as the old part number T44 and same as new part number 3000005090.
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Mantle String Tie #21 4 Pack - M02
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
-
Filler Cap Screw 220 Size - S68
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
-
Mantle String Tie #21 2 pack - M03
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345.
-
Ball Nut, 2 Pack - C011
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384. -
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
Generator Nut, Used - S105
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
-
Air Tube Screw - S72
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
-
Generator Nut - S142
Generator nut. Fits many models of lanterns which take the 220E5891 generator: 220s, 228's, 275. Also fits many other models. Find your parts diagram HERE and verify the generator nut is listed as 605-210.
-
220/228 Air Tube Screw Phillips - S74
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
-
Wrench 220B - R300
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
-
Pump Assembly Leather Used Square Nut - U810
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
Rebuild Kit - 220 & 228 Lanterns - K02
Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.
Includes:
- 4 Coleman string tie mantles for your lantern
- 1 Coleman generator
- 1 Leather replacement pump cup for the bottom of the thumb operated air pump
- 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
- 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed
See Diagram in "Description" under photo at bottom left of this page
-
Fuel Tube Spring, Stainless - R581
New stainless fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
-
Valve Wheel Black Old Style, Used - S113
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
-
Air Stem, Old Style, Used - S107
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
-
-
252 Direction Disk - S10
Direction disk for the military lanterns. These came out of the old SMP factory.
-
Black Valve Wheel New Style, Used - S112
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
-
327 Mica Globe - G09
This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
-
Check Valve Old Style - R425
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
-
Tip Cleaner Stem Reproduction - R700
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3
-
-
-
Burner Tube Brass 2 7/8 - E1254
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
-
220/228 Valve Bushing Set - S134
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
-
Burner Cap 220 Brass Hex - S32
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
-
220 Globe White Letter Germany - G05
German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
220 Red Logo Replacement Globe USA - G22
This is a US made replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Burner Cap 220 Steel Hex - E1267
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
-
-
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
-
Nut For 220 Used - E1587
Used frame hold down nut for the models 220/228B through 220/228F lanterns. Will show sings of light rust and wear but should work fine. Will also work on CQ Lamps to hold down the handle.
-
Burner Tube Short/Slant - S135
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
-
Filler Cap Gasket for 3 Piece Cap- 10 PACK - S41🔟
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
-
Pump Assembly, Universal - C45
Universal pump assembly with leather cup that fits almost all Coleman lanterns and stoves. Does not fit the small Peak 1 lanterns or stoves, some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
-
Two Mantle Direction Disk USA Reproduction - S02
New reproduction direction disk for the many of the 2 mantle lanterns made in the USA like the 220 and 228 models B thru F. These are aluminum and look and feel identical to the original, and they are made here in the USA. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantles" as opposed to "mantle" for a single mantle lantern.
-
Coleman Filter Funnel - C24
New Filter Funnel For Lamps And Stoves.
Stops filling your lantern or stove at the correct level.
-
Burner Tube 2 1/2 Inch - E1471
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.