226-700
-
Generator Lantern - C24
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
This also fits 222 models, but please read on.Â
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using  this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.Â
-
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part number 242-6201.
Made of 100% graphite.
-
Generator Tube Packing - P5
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
-
Pump Assembly - E88
NOS Pump assembly. Comes with the pump leather and metal cap. Fits the small backpacking 400 series stoves and 222, 226, 229 series lanterns. -
Used Pump Assembly - E908
Used Pump assembly. Comes with the pump leather and metal cap. Fits the small backpacking 400 series stoves and 222, 226, 229 series lanterns.
-
New Filler Cap Brass - C4
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.Â
Has gone in the past by part numbers 220C1401, and now 425A1405
-
Globe 222 Clear - G14
Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
-
Push On Nut Small - S4
Push on nut for end of pump rod. The small push on nut is used with leather pump cups.
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.Â
Typically used to stop a fuel leak from the valve stem on older appliances.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part numberc 118B6201 and 118D6201.Â
-
Pump Plunger - C51
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup.
-
Filler Cap 3 Piece Red Used - E310
This cap will fit most models of lanterns. It is a used cap and will have some missing paint with the brass showing through in places. Has a new cap gasket installed.
-
Pump Plunger - C29
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the small backpacking 400 series stoves and 222, 226, 229 series lanterns.
-
Filler Cap Tire Valve Nickel - R218
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Brass - R236
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
-
Filler Cap 3 Piece Green Used - E244
This is a used green 3 piece filler cap. Has a new gasket. They are in various stages of wear. Paint is chipped or missing.
-
O-Ring Set Canadian Blue - S35
Set of 3 flourosilicone O-rings for Canadian made Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so you should be able to rebuild whatever you have.
Does Work on the 533.
Does not work on the 442.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
Filler Cap 3 Piece Nickel Plated Used - E677
Used nickel plated 3 piece cap. This item is used and may show spots of missing nickel, scratches, or light wrench marks. Gaskets have been replaced with new.Â
-
Push On Nut Large - S1
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
-
Filler Cap 3 Piece Used Copper Color - E556
This is a used 3 piece filler cap made of brass. Paint is worn and has a new filler cap gasket. Copper in color. Has wrench marks.
-
Window Decal - Lantern Green - D101
Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Lantern White - D103
Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal Lantern - Flat Black - D104
Window decal for glass or a hard surface - flat black in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Lantern Red - D102
Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Check Valve O Ring - S36
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
-
Window Decal - Sunrise Green - D105
Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Sunrise Red - D106
Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Sunrise White - D107
Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Check Valve - Stem ONLY - E946
Used - fits model 400 stove, 226 lantern. Has the smaller threads used on the newer style check valves. 3-3/4" long.