226A
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Filler Cap, Brass - C004
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
-
Mantles #20 String Tie 2 Pack - M06
String Tie Mantles for Models 222, 226, 229, and 3022 lanterns
Also known as part number 3000004346.
-
Check Valve O Ring - S20
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
-
Pump Cup, Neoprene - C019
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
-
Generator Lantern - C31
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
-
O-Ring - S21
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
- The fuel tube on the 550B stove
- On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251
-
Filler Cap Tire Valve Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Small Pump Plunger - C35
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.
-
Globe 222 Clear - G14
Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
Also known as part number 5010000290.
-
Bail Wrap Protector Black - R513
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
-
Large Push On Nut for Neoprene Cups - S09
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
-
Small Pump Plunger - C37
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203
-
Metal Funnel Small - R503
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
-
Filler Cap Green Used - U803
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.
-
Filler Cap Gasket for 1 Piece Cap - 10 PACK - S42🔟
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
-
Filler Cap Gray Used - E1307
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
-
Filler Cap 3 Piece Red Used - U800
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
-
Large Valve Stem Packing - 10 PACK - P01🔟
This is a10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Bail Wrap Protector Clear - R512
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
-
-
Mica Globe Panels - E1120
These mica panels are 3" x 5" in size.
General information:
- Mica can be cut with sharp scissors or a good paper cutter
- This is the only size that is available
- Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
- Mica is not available in amber or red.
- Mica can withstand temperatures up to 1800 degrees F.
- These are only sold in a package of 5 panels.
-
222 Mica Globe - G21
Mica globe for the small backpacking lanterns. Will fit models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
Would be good for camping as it will not break like glass.
-
Filler Cap, 3 Piece, Blue, Used - E1624
This is for one used 3 piece blue filler cap. Shade and wear may vary.
Comes with a new gasket that you will have to install.
-
Reproduction 226 Generator - R205
Reproduction Generator for Model 226A700 and the 226-700. Generator includes new gas tip, spring, and tip cleaning wire.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend the 226 generator as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
-
Filler Cap Brown Used - E1026
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
-
Filler Cap Dark Green Used - E1431
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
-
Filler Cap Steel, Used - E1386
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
-
222 USA Globe - G250
Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
Also known as part number 5010000290.
-
Filler Cap Steel, NOS - E1554
NOS steel filler cap for Coleman lanterns. Comes in original packaging
-
226 NOS Generator - E1013
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
-
Air Stem, NOS - E1594
NOS - fits model 400 stove, 226 lantern. Has the smaller threads used on the newer style check valves. 3-3/4" long.
-
Filler Cap Silver Used - E1385
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Silver in color. Includes a new gasket for you to install.