228 Slant
-
Cap Gasket - S56
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as cap gasket 118B1361 but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Pump Assembly 220B Brass Thin Used - E1420
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. I have pictured both styles. They are interchangeable. You are purchasing the style one labeled "Thin" with the thinner knurled portion. Make sure you get the one you want.
-
Air Stem Old Style Long Used - E1358
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
-
-
220 Globe Green Sunrise Logo - G24
This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects.
The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"
This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.
-
-
-
Burner Cap 220 Steel Hex - E1267
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
-
Burner Cap 220 Brass Hex - S92
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
-
Pump Assembly 220B Thick Used - E1007
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape.
-
Pump Assembly 220C Steel Cap Used - E1296
This is a used pump assembly for the model 220C. It has a steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape.
-
220 Globe 1936-1945 - G72
This is an original used globe made between 1936 to 1945 for Coleman lanterns that used the 220 size globe. Although used, it has been inspected for damage or defects (this one has a small bubble shown in picture) Please note that the green straight line logo used on these globes was very lightly stamped and can sometimes be difficult to see. This was normal for the time period. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Ball Nut Used - S18
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
-
-
Burner Tube Short - S132
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
-
Check Valve Old Style - S179
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
-
-
Generator Q77 Steel - E1005
Steel body Q77 generator. Probably made during WWII or possibly even WW1. New old stock but very tarnished from age.
-
Air Stem Long New Style - E1048
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
-
220 Globe White Letter Germany - G90
German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
220 Globe WL Mexico - G106
Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Generator Nut -S173
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
-
Pump Assembly 220B Brass Used - E1054
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape.
-
Slant Burner Top Half Used - E1305
Used top half of the burner assembly for a slant lantern or lamp.
-
220 Red Logo Pyrex Globe USA - G28
This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.
-
220 White Logo USA Globe - G91
USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Slant Valve Bracket - E1198
Only 1 left in stockSlant valve bracket used in the 220/228 slant and lamp models 117, 118, and 119 table lamps.