228D
-
Rebuild Kit - 220 & 228 Lanterns - K2
Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.
Includes:
- 4 Coleman string tie mantles for your lantern
- 1 Coleman generator
- 1 Leather replacement pump cup for the bottom of the thumb operated air pump
- 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
- 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed
See Diagram in "Description" under photo at bottom left of this page
-
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Mantle Insta-Clip 2 #21 2 pack - M13
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
-
Generator Lantern - C2
New generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Same generator as the old part number T44. Same as new part number 3000005090.
-
220 Globe Green Sunrise Logo - G24
This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. The light green logo is very light as was common. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.
-
220 Red Logo Replacement globe USA - G22
This is a US made replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
220 Globe 1936-1945 - G72
This is an original used globe made between 1936 to 1945 for Coleman lanterns that used the 220 size globe. Although used, it has been inspected for damage or defects. Please note that the green straight line logo used on these globes was very lightly stamped and can sometimes be difficult to see. This was normal for the time period. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
220 White Logo USA Globe - G63
USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Globe 220 Red Sunrise - G23
Used red sunrise globe used on Canadian lanterns. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Mantle String Tie #21 2 pack - M3
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Mantle String Tie #21 4 Pack - M2
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Peerless Mantles 2C-HG - M1
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
Peerless Mantles 24-A - M4
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part number 242-6201.
Made of 100% graphite.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Leather Pump Cup And Back-Up Plate - C6
Leather pump cup, push on nut and back-up plate. New part number 3000005094.
-
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
-
Push On Nut Small - S4
Push on nut for end of pump rod. The small push on nut is used with leather pump cups.
-
-
Decal - Fits 1945 to 1946 - 220C & 228C Lanterns- D33
Instruction Decal for 1945 to 1946 220C & 228C Lanterns. Also fits some 220D & 228D Lanterns
-
Tip Cleaner Stem Reproduction - R244
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
-
Mixing Chamber New Style Plated - E189
This is a newer style mixing chamber for the 220-228 series lanterns. It is plated with a zinc coating or something similar. -
Pump Assembly Leather Used Square Nut - E981
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
Valve Assembly Used - E16
This is a used valve assembly for the models 220/228B through 220/228F lanterns. It has been cleaned. New valve packing has been installed. It is ready for use and should work as well as a new one.
-
Black Valve Wheel New Style USED - S78
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
-
Screw Phillips Head - S74
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
Decal - Fits 220 & 228 D Lanterns - D43
This is the decal used on the early painted 220D/228D transitional lantern.
-
Burner Tube Short - S132
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
-
Burner Tube 2 1/2 Inch - E32
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size. -
Push On Nut Large - S1
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
-
-
Generator Tube Packing - P5
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
-
Ventilator 220F Used #15
This is a used ventilator. It will fit models 220F. The 220F vent is slightly smaller than the 220H through 220K vent and may not fit those models. It has the chips and rust as shown.
-
Burner Tube Brass 2 3/4 - E448
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long. -
Screw Flat Head - S71
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
-
-
-
Air Stem Used Old Style - S31
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
-
Check Valve With Stem - C1
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 check valve then this would be the correct part.
-
Burner Tube Brass 2 7/8 - E36
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
-
-
-
-
New Filler Cap Brass - C4
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Has gone in the past by part numbers 220C1401, and now 425A1405
-