228E
-
Rebuild Kit - 220 & 228 Lanterns - K2
Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.
Includes:
- 4 Coleman string tie mantles for your lantern
- 1 Coleman generator
- 1 Leather replacement pump cup for the bottom of the thumb operated air pump
- 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
- 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed
See Diagram in "Description" under photo at bottom left of this page
-
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Mantle Insta-Clip 2 #21 2 pack - M13
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
-
Screw Flat Head - S71
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
-
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part number 242-6201.
Made of 100% graphite.
-
Air Stem Used Old Style - S31
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Leather Pump Cup And Back-Up Plate - C6
Leather pump cup, push on nut and back-up plate. New part number 3000005094.
-
Mantle String Tie #21 2 pack - M3
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Burner Tube Brass 2 7/8 - E36
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
-
-
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
-
-
New Filler Cap Brass - C4
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Has gone in the past by part numbers 220C1401, and now 425A1405
-
Ventilator 220F Used #1
This is a used ventilator. It will fit models 220F. The 220F vent is slightly smaller than the 220H through 220K vent and may not fit those models.
-
Generator Lantern - C2
New generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Same generator as the old part number T44. Same as new part number 3000005090.
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.
Typically used to stop a fuel leak from the valve stem on older appliances.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part numberc 118B6201 and 118D6201.
-
-
-
220 Globe Clear - G4
This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. New part number 2000026613.
-
Mantle String Tie #21 4 Pack - M2
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Decal - Fits 1951 200A & 1951 thru 1953 220 & 228E Lanterns - D17
Coleman Lantern Logo for 1951 200A and 1951 thru 1953 220 & 228E Lanterns
-
Decal - Fits 1954 to 1961 220 & 228 E Lanterns - D18
Coleman Lantern Logo for 1954 to 1961 220 & 228 E Lanterns
-
Decal - Fits 1962 to 1964 200A, 220 & 228 E & F Lanterns - D13
No Border Logo with "Reg." & "Lantern" for 1962 to 1964 200A, 220 & 228 E & F Lanterns
-
-
Filler Cap Tire Valve Nickel - R218
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Brass - R236
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Ventilator 220F Used #2
This is a used ventilator. It will fit models 220F. The 220F vent is slightly smaller than the 220H through 220K vent and may not fit those models. This vent has rust as shown.
-
Ventilator 220F Used #3
This is a used ventilator. It will fit model 220F. The 220F vent is slightly smaller than the 220H through 220K vent and may not fit those models. This vent has wear as shown. Has rust around ball nut area.
-
Ventilator 220F Used #8
This is a used ventilator. It will fit model 220F. The 220F vent is slightly smaller than the 220H through 220K vent and may not fit those models. This vent has the chips shown.
-
Tip Cleaner Stem Reproduction - R244
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
-
Burner Cap 220 Steel Hex - E70
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
-
Burner Cap 220 Brass Hex - S92
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
-
-
Mixing Chamber New Style Plated - E189
This is a newer style mixing chamber for the 220-228 series lanterns. It is plated with a zinc coating or something similar. -
Burner Tube Steel - E162
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
-
Filler Cap Red Chipped - E91
Used filler cap that fits most Coleman lanterns and stoves. Paint is chipped with a few wrench marks.
-
Peerless Mantles 2C-HG - M1
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
Peerless Mantles 24-A - M4
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
-
Pump Assembly Leather Used Square Nut - E981
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
Burner Tube Nickel Plated - E120
This is a nickel plated brass burner tube. Not polished. More of a utilitarian type finish. For most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. -
220 Burner Screen - S90
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
-
Parts Safe Gasket 220 - E62
This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.
-
Collar 228E Transitional Used - X9
This is a used collar for the transitional 228E lantern. Ribbed like a 228F collar but stamped 228E