228J
-
Rebuild Kit - 220 & 228 Lanterns - K2
Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.
Includes:
- 4 Coleman string tie mantles for your lantern
- 1 Coleman generator
- 1 Leather replacement pump cup for the bottom of the thumb operated air pump
- 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
- 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed
See Diagram in "Description" under photo at bottom left of this page
-
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Mantle Insta-Clip 2 #21 2 pack - M13
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Generator Lantern, Reproduction - R205
Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
-
-
Generator Lantern - C02
New generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Same generator as the old part number T44. Same as new part number 3000005090.
-
220 Globe Green Sunrise Logo - G24
This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects.
The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"
This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.
-
220 Globe 1936-1945 - G72
This is an original used globe made between 1936 to 1945 for Coleman lanterns that used the 220 size globe. Although used, it has been inspected for damage or defects (this one has a small bubble shown in picture) Please note that the green straight line logo used on these globes was very lightly stamped and can sometimes be difficult to see. This was normal for the time period. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Mantle String Tie #21 2 pack - M03
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Mantle String Tie #21 4 Pack - M02
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Peerless Mantles 2C-HG - M01
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
Peerless Mantles 24-A - M04
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
Generator Tube Packing - P05
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
-
-
Air Stem Used Old Style - S31
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
-
Check Valve With Stem - C01
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part. The latest part number for this is 2006381ZCL.
-
Leather Pump Cup And Back-Up Plate - C05
Leather pump cup, push on nut and back-up plate. New part number 3000005094.
-
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
New Filler Cap Brass - C04
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Has gone in the past by part numbers 220C1401, and now 425A1405
-
-
-
Valve Assembly Used - E1254
Used valve assembly that has been cleaned and has new valve stem packing. Will work perfectly. Fits models 220H-J & 228H-J and 220K lantern.
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
-
-
Neoprene Pump Cup And Nut - C08
Brand new Neoprene Pump Cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
-
Filler Cap Green Used - E1248
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear.
Comes with a new gasket.
-
-
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Burner Cap 220 Steel Hex - E1267
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
-
Burner Cap 220 Brass Hex - S92
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
-
Mixing Chamber 220J - E1014
This is a mixing chamber for the model 220-228J and 220K lanterns. It would also be correct for later 220-228H lanterns. Comes with the new vent rod.
-
-
-
-
Burner Tube Steel - E1480
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
-
Pump Assembly Leather Used Square Nut - E1256
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
220 Burner Screen - S90
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
-
Parts Safe Gasket 220 - E1446
This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.
-
Filler Cap 3 Piece Green Used - E1265
This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket NOT installed.
-
Valve Wheel Black Old Style Used - S79
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
-
Black Valve Wheel New Style USED - S78
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
-
-
Ball Nut Used - S18
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
-
Screw Phillips Head - S74
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.