228K

Products: 150 of 84
Show: 50
  • Rebuild Kit - 220 & 228 Lanterns - K2

    Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.

    Includes:

    • 4 Coleman string tie mantles for your lantern
    • 1 Coleman generator
    • 1 Leather replacement pump cup for the bottom of the thumb operated air pump
    • 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
    • 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

    See Diagram in "Description" under photo at bottom left of this page

    Not rated yet
    • $30.25
  • Mantles, Insta-Clip #21, 2 pack - M12

    Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

    These simply slide on and you cross the wires instead of tying strings - very quick to install.

    Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

    Not rated yet
    • $3.75
  • Mantle Insta-Clip 2 #21 2 pack - M13

    Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

    Not rated yet
    • $4.55
  • Sparker Flints Zippo - E281

    Zippo brand Flints for the Coleman Lantern Spark Igniter.

    Not rated yet
    • $4.25
  • Generator Lantern - C2

    New generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Same generator as the old part number T44. Same as new part number 3000005090.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $16.35
  • 220 Globe Green Sunrise Logo - G24

    This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

    The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

    This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

    Not rated yet
    • $35.00
  • 220 Red Logo Replacement globe USA - G22

    This is a US made replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

    Not rated yet
    • $24.00
  • 220 Globe 1936-1945 - G72

    This is an original used globe made between 1936 to 1945 for Coleman lanterns that used the 220 size globe. Although used, it has been inspected for damage or defects. Please note that the green straight line logo used on these globes was very lightly stamped and can sometimes be difficult to see. This was normal for the time period. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

    Not rated yet
    • $40.00
  • Mantle String Tie #21 2 pack - M3

    Coleman's Most Popular Sized Mantles. 2 mantles per pack

    Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

    Not rated yet
    • $3.45
  • Mantle String Tie #21 4 Pack - M2

    Coleman's Most Popular Sized Mantles. 4 mantles per pack

    Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

    Not rated yet
    • $6.45
  • Peerless Mantles 24-A - M4
    • New!

    Peerless Mantles 24-A - M4

    These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $2.70
  • Leather Pump Cup - S81

    This is the common Coleman pump cup that fits most lanterns and stoves. 

    Has a 7/8 inch diameter and is made of oiled leather.

    Score: 3.33 (votes: 3)
    Reviews: 3
    |
    3
    • $3.45
  • Ball Nut - S9

    New Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

    Not rated yet
    • $3.00
  • Push On Nut Small - S4
    • Free Shipping

    Push On Nut Small - S4

    Push on nut for end of pump rod. The small push on nut is used with leather pump cups.

    Not rated yet
    • $3.00
  • Pump Clip - S22
    • Free Shipping

    Pump Clip - S22

    Pump Clip

    Not rated yet
    • $3.00
  • Push On Nut Large - S1
    • Free Shipping

    Push On Nut Large - S1

    Push on nut for pump. The large push on nut is used with the neoprene pump cup.

    Not rated yet
    • $3.00
  • Generator Tube Packing - P5

    This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.

    Not rated yet
    • $2.30
  • Air Stem Used Old Style - S31

    Air stem older style used. Has the larger head on the end.

    In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

    Not rated yet
    • $4.50
  • Check Valve With Stem - C1

    This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $8.65
  • Ball Nut 2 Pack - C16

    Ball Nut 2 Pack.

    Not rated yet
    • $5.40
  • 220 Filler Cap Insert - S144

    This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

    Not rated yet
    • $7.40
  • New Filler Cap Brass - C4

    New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

    Has gone in the past by part numbers 220C1401, and now 425A1405

    Not rated yet
    • $8.85
  • Fuel Air Tube - E12

    Fuel air tube for model 220 & 228 through B through K lanterns.

    Not rated yet
    • $9.50
  • Large Valve Stem Packing - P1

    Typically used to stop a fuel leak from the valve stem on older appliances.

    This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

    If you need to check your model, please see the PARTS DIAGRAM PAGE

    425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

    Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

    Made of 100% graphite.

    Not rated yet
    • $3.25
  • U Clip - S11

    Fits model 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns. 

    Same as part number 206A1251

    Not rated yet
    • $3.00
  • Generator Nut - S176

    Generator nut.

    Not rated yet
    • $5.40
  • Neoprene Pump Cup And Nut - C11

    Brand new Neoprene Pump Cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.

    Not rated yet
    • $4.25
  • 220 Globe Clear - G4

    This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. New part number 2000026613.

    Not rated yet
    • $16.50
  • Decal - Fits 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns - D11
    • Free Shipping

    Decal - Fits 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns - D11

    White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.



    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $3.25
  • Filler Cap Green Used - E258

    This is a used one piece filler cap. Paint is chipped. Has a new filler cap gasket. These are green. The shade of green and wear varies within this stock of used caps. 

    Not rated yet
    • $10.00
  • Spark Igniter - C8

    Spark Igniter

    Not rated yet
    • $15.25
  • Filler Cap Tire Valve Nickel - R218

    This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

    Not rated yet
    • $12.70
  • Burner Cap 220 Steel Hex - E70

    Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

    Not rated yet
    • $3.00
  • Burner Cap 220 Brass Hex - S92

    Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.

    Solid brass with stainless steel screen.

    Same part number as 112-323

    Not rated yet
    • $4.75
  • Mixing Chamber 220J - E163

    This is a mixing chamber for the model 220-228J and 220K lanterns. It would also be correct for later 220-228H lanterns. Comes with the new vent rod.

    Not rated yet
    • $5.00
  • Pump Cup Neoprene - S13

    Pump Cup Neoprene for most lanterns

    Not rated yet
    • $3.25
  • Vent Rod 220 Short - S148

    Shorter vent rod for models 220/228F through 220K

    Not rated yet
    • $5.00
  • Burner Tube Steel - E162

    Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

    Not rated yet
    • $3.00
  • U Clip Used - S12

    Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns. 

    Same as part number 288-1251

    Not rated yet
    • $0.25
  • Pump Assembly Leather Used Square Nut - E264

    This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

    Not rated yet
    • $12.50
  • 220 Burner Screen - S90
    • Free Shipping

    220 Burner Screen - S90

    Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $1.90
  • Vent 228F Used #10

    This is a used vent for models 228F through 228J. Has some paint chips as shown in picture.      

    Not rated yet
    • $15.00
  • Vent 228F Used #12

    This is a used vent for models 228F through 228J. Has some paint chips as shown in picture, and a small dent on one side of the top of the vent.

    Not rated yet
    • $15.00
  • Vent 228F Used #13

    This is a used vent for models 228F through 228J. It has a few paint chips as shown in picture. 

    Not rated yet
    • $18.00
  • Burner Tubes Used Lot of 10 - E199

    This is a lot of 10 used brass 220 size burner tubes and caps. The caps will all have screens. Most of the burner caps are steel but some are brass. All the burner tubes are brass. I created this product for the guys that like to build fish gigging lights. A low cost alternative to buying all new burner tubes and caps.

    Not rated yet
    • $22.00
  • Valve Wheel Black Old Style Used - S79
    • New!

    Valve Wheel Black Old Style Used - S79

    This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.

    Not rated yet
    • $11.00
  • Black Valve Wheel New Style USED - S78
    • New!

    Black Valve Wheel New Style USED - S78

    This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A

    Not rated yet
    • $8.50
  • Nut - Frame Bottom - E67

    Nut for 220H through K frame bottom.

    Not rated yet
    • $2.00
  • Ball Nut Used - S18

    Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

    Not rated yet
    • $2.75
  • Screw Phillips Head - S74

    Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.

    Not rated yet
    • $0.25
Products: 150 of 84
Show: 50