222B

Reproduction filler cap gasket for Coleman one-piece fuel caps. Fits many Coleman lanterns and stoves that use the 1-piece filler cap without a center bolt or screw. Good quality replacement that helps stop fuel leaks. If your cap looks like the one in the photo, this is the right gasket. 

Look HERE for how to install these. Green cap shown for illustration only and is not included.

Also known as part number 425A1361

Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

String Tie Mantles for Models 222, 226, 229, and 3022 lanterns. May be in different packing than what is pictured.

Also known as part number 3000004346.

Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.

Also known as part number 3000005094.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

New Coleman-manufactured pump cup designed for all lanterns that originally utilized the rubber-style cup.

Also known as part number 639-1091.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

Pump Clip

New Coleman Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.

Also known as part number 3000005088.

This also fits 222 models, but please read on. 

Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using  this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605. 

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

Fits the fuel tube on all appliances that have a plastic fuel and air tube.  

Models: 214, 282, 285, 288, 290, and 295.

Also fits: 

• The fuel tube on the 508, 508A & 550B stoves
• On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251

10-pack of reproduction filler cap gaskets for Coleman one-piece fuel caps. Smart value for many Coleman lanterns and stoves using the standard 1-piece cap without a center bolt. Keeps spares on hand so your gear stays leak-free on the next trip. 

Look HERE for how to install these. Red cap shown for illustration only.

Also known as part number 425A1361

Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.

Stainless Steel burner frame to valve nut for the 200, 200A, 201, 202, 222, 222A, 222b, 237A, 237B, all the 242s, 321B, 325A, 331, 335, 339, 621A, 621B and 635 lanterns. May also fit other models and some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Also listed in diagrams as part number 604A456.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8

This has been reported to be the correct size to repair the valve on the 400B, 533, and the 533A stoves. Only one is needed for each.

Will also work on 533B - one of these is needed along with the Viton #8

This is a high-quality reproduction of the older style check valve designed to accommodate an original air stem with the larger ends. This part does not include an air stem, as it is intended for use with your existing old-style stem.

Fits models requiring part numbers 200-6381, 400-6381, 242B5381, or 621-5361.

10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width. 

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.

Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter. 

Also known as part number 5010000290 & 5414-0481

Used generator nut for these models: 214, 229, 286, 288, 290, 321, 335, 621, 635, 639 and 3022. 

May fit others. Also known as part number 335-2101

This is the short pump used on the small stoves and lanterns. Smaller stoves and lanterns with the plastic top are what this is for. Some small series stoves (Peak) and lantern model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #5

New Reproduction Generator Needle for Model 222, 222A, 222B, 226 and the 229.

Filler cap lanyard for the small backpacking lanterns. 

Mica globe for the small backpacking lanterns. Will fit models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.

Would be good for camping as it will not break like glass.

New plastic tank/fount bumper that can be used on Models 222, 222A, 222B, 226, 226A and 229 lanterns. These are made in Colorado for us by a lantern and stove enthusiast.  Plastic is flexible and won't scratch the paint of your fount.  

Reproduction Generator for Model 226A700 and the 226-700. Generator includes new gas tip, spring, and tip cleaning wire.

This also fits 222 models, but please read on. 

Coleman discontinued the 222 generator, and they recommend the 226 generator as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605. 

Reliable check valve removal tool crafted in the USA (Washington State), from high-quality steel. Designed for Coleman lanterns and stoves—handles both thicker original stems and slimmer modern ones with its two rods. Built to make the job straightforward every time. Backed by our lifetime warranty: if it breaks at any time, we will replace it or give you a full refund.

How to Use Your Check Valve Removal Tool

Important: Your tool is backed by our lifetime warranty against defects in materials or workmanship. As long as it's used correctly and breaks under normal use (not from misuse, excessive force, or improper engagement), we'll stand behind it. Contact us anytime with questions or issues.

Follow these steps carefully to remove and reinstall the check valve safely:

1. Identify the check valve type. Pull out the air stem (pump rod) and match its threads to one of the tool's rods: Large or Small. (Most pre-1980s Coleman models use the Large size; newer ones often use Small.)
2. Thread the rod into the check valve. Hand-screw the matching rod into the check valve threads, finger-tight only. Aim to bottom it out or engage as many threads as possible—adding a drop of light lubricant (like oil) can help if it's stubborn. Critical: If it only turns one or two rotations and doesn't catch properly, stop! That's not enough thread engagement, and forcing it could damage the valve or tool.
3. Assemble the tool. Slide the outer tube down over the threaded rod.
4. Engage the prongs. Gently rotate the outer tube until the prongs fully seat into the check valve's grooves/slots. (Note: On early valves, the fit may feel tight; on later ones, it may feel looser due to natural Coleman manufacturing variations—this is normal.)
5. Secure the assembly. Screw the wing nut onto the exposed end of the rod to lock the tube and prongs in place. Tighten it snugly by hand—do not over-tighten, as this could strip the valve threads.
6. Remove the check valve. Use a long crescent wrench on the tool's flats. Hold the fount steady (a second person helps here) and turn the wrench quickly counterclockwise to break it loose. If it's really stuck, tap the long wrench handle sharply with your fist or a rubber mallet for a controlled shock—often more effective than steady pressure. Once loose, finish unscrewing by hand.

To reinstall the check valve: Simply reverse the steps above.

• Tighten only until snug—do not over-tighten as you can damage your new check valve’s threads.
• No thread sealant is required, though a light lubricant on the threads can make future removal easier.

If you run into any trouble or have questions about your specific Coleman model, feel free to reach out—we're happy to help!

For more great Coleman repair tips and community advice, check out the Old Coleman Parts Collector forum: www.colemancollectorsforum.com

New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.

Also known as part number 3000005088.

This also fits 222 models, but please read on. 

Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using  this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605. 

Used - fits model 400 stove, 226 lantern. Has the smaller threads used on the newer style check valves. 3-3/4" long.

NOS filler cap with lanyard for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap.

Stud.

Used filler cap with lanyard for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap. Lanyard on this one is a little rough but still intact.

Comes with a new gasket that you will have to install.

NOS gas tip for Model A Lamps and possibly other early Torch-Lite Lamps.

Used filler cap for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap. Does not come with lanyard.

Comes with a new gasket that you will have to install.

Used filler cap for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap. Does not come with lanyard.

Comes with a new gasket that you will have to install.