238B

Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Replacement Check Valve and Air Stem This is the standard replacement part for most Coleman lanterns and stoves manufactured after 1946, as well as select earlier models. It features the updated design with a smaller air stem head; the included new stem is designed to replace your existing one entirely.

Fits models requiring part numbers 242B5381, 621-5361, or 2006381ZCL.

These are treated with Thorium from the factory and are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns. 

Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.

Also known as part number 3000005094.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This new Coleman globe will fit models 236, 237, 237A, 237B 635, 639, 639A, 639B, and 639C. Top and bottom opening measures 4-7/8" OD and is 5-1/4" tall.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

This is a high-quality reproduction of the older style check valve designed to accommodate an original air stem with the larger ends. This part does not include an air stem, as it is intended for use with your existing old-style stem.

Fits models requiring part numbers 200-6381, 400-6381, 242B5381, 242B538 or 621-5361.

10-pack of reproduction leather pump cups for Coleman lanterns and stoves. Smart value so you have spares on hand for future trips. Fits the same Coleman models that use the standard leather pump cup. Helps keep your gear pumping smoothly.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a very nice reproduction bail handle for the model 236 and 237 lanterns. Made of spring steel here in the USA.

Original NOS Coleman pump cup that fits most lanterns and stoves, they have been sitting around for many years and may not have their perfect shape and some are almost flat.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Single Ball Nut. Fits all Coleman lanterns except the 242 type models. In good shape - just dirty.

This is a used pump square nut.

Comes with one square nut ONLY.

Original NOS Coleman pump cup that fits most lanterns and stoves.

They are flat and have lost most of their shape from sitting around over the years

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

Reliable check valve removal tool crafted in the USA (Washington State), from high-quality steel. Designed for Coleman lanterns and stoves—handles both thicker original stems and slimmer modern ones with its two rods. Built to make the job straightforward every time. Backed by our lifetime warranty: if it breaks at any time, we will replace it or give you a full refund.

Also has been reported that it works on "some" AGM check valves.

How to Use Your Check Valve Removal Tool

Important: Your tool is backed by our lifetime warranty against defects in materials or workmanship. As long as it's used correctly and breaks under normal use (not from misuse, excessive force, or improper engagement), we'll stand behind it. Contact us anytime with questions or issues.

Follow these steps carefully to remove and reinstall the check valve safely:

1. Identify the check valve type. Pull out the air stem (pump rod) and match its threads to one of the tool's rods: Large or Small. (Most pre-1980s Coleman models use the Large size; newer ones often use Small.)
2. Thread the rod into the check valve. Hand-screw the matching rod into the check valve threads, finger-tight only. Aim to bottom it out or engage as many threads as possible—adding a drop of light lubricant (like oil) can help if it's stubborn. Critical: If it only turns one or two rotations and doesn't catch properly, stop! That's not enough thread engagement, and forcing it could damage the valve or tool.
3. Assemble the tool. Slide the outer tube down over the threaded rod.
4. Engage the prongs. Gently rotate the outer tube until the prongs fully seat into the check valve's grooves/slots. (Note: On early valves, the fit may feel tight; on later ones, it may feel looser due to natural Coleman manufacturing variations—this is normal.)
5. Secure the assembly. Screw the wing nut onto the exposed end of the rod to lock the tube and prongs in place. Tighten it snugly by hand—do not over-tighten, as this could strip the valve threads.
6. Remove the check valve. Use a long crescent wrench on the tool's flats. Hold the fount steady (a second person helps here) and turn the wrench quickly counterclockwise to break it loose. If it's really stuck, tap the long wrench handle sharply with your fist or a rubber mallet for a controlled shock—often more effective than steady pressure. Once loose, finish unscrewing by hand.

To reinstall the check valve: Simply reverse the steps above.

• Tighten only until snug—do not over-tighten as you can damage your new check valve’s threads.
• No thread sealant is required, though a light lubricant on the threads can make future removal easier.

If you run into any trouble or have questions about your specific Coleman model, feel free to reach out—we're happy to help!

For more great Coleman repair tips and community advice, check out the Old Coleman Parts Collector forum: www.colemancollectorsforum.com

One mantle per pack. Used on 500-550 candlepower lanterns. Made in USA

This is a reproduction generator for the very rare 238B lantern. These generators have been impossible to find for many years. Now you can get that rare 238B of yours running again. They were not cheap to get made but the workmanship is excellent. New generator includes new gas tip, spring, and tip cleaning wire.

Vintage 200A Reproduction splined ball nut. Will fit all Coleman lanterns except the 242 type models.

This is a reproduction bail handle for the model 236 and 237 lanterns.

They are new but a little rusty and warped/bent - they can be fixed with a little patience and a propane torch.

Gas tip for the 238B lantern.

Large size Sears globe wrap which will show off your lantern and protect the glass during travel. These are easy to attach with Velcro. We don't believe these will fit any Sears double mantle due to a conflict with the bail handle, so these would have to be displayed most likely on a Coleman lantern.

Will fit on any lantern that uses the 220/290A/295 style globe as long as the bail handle terminates on the vent of the lantern. Make sure your bail handle hinges at the vent - otherwise it will be in the way  - see the last photo for clarification about the bail location issue.

Will fit well on the 290A, 290B and 295. Fits tightly on the 236, 237, 238, 635 and 639. Look at the photos to get an idea of how they fit - only first photo has this products design.  Will conflict with the bail on all 220 and 228 models.

These will melt, so your lantern has to be cool. Made of neoprene fabric and Velcro here in the USA.

This globe will fit models 236, 237, 237A, 635, 639, 639A, 639B, and 639C.

These are treated with Thorium from the factory and are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.