229-700 Peak 1

Knob

Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.

Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.

String Tie Mantles for Models 222, 226, 229, and 3022 lanterns

Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the small backpacking 400 series stoves and 222, 226, 229 series lanterns.

Pump Cup Neoprene for most lanterns

This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. 

If your filler cap has a screw in the center of it then this gasket will not work. 

The red filler cap is shown for illustration purposes only and is not included.

Used globe for the Peak 1 lantern Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.

Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - flat black in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Used - fits model 400 stove, 226 lantern. Has the smaller threads used on the newer style check valves. 3-3/4" long.