234
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.Â
Has a 7/8 inch diameter and is made of oiled leather.
-
Mantle String Tie #21 2 pack - M3
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
GAS TIP - GT2
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
-
-
Burner Tube with Nut - Steel - E443
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long. -
Burner Tube Brass - E39
Burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long. -
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.Â
Typically used to stop a fuel leak from the valve stem on older appliances.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part numberc 118B6201 and 118D6201.Â
-
Filler Cap Gasket - S47
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.Â
Also fits the model 500 stove. The green filler cap is shown for identification purposes only and is not included.
-
-
Globe 237 Clear - G6
This globe will fit models 236, 237, 237A, 237B 635, 639, 639A, 639B, and 639C.
-
Mantle String Tie #21 4 Pack - M2
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
200A Globe Clear - G1
This is a brand new clear globe that will fit models 200, 200A, 200B, 201, 202, 242A, 242B, 242C, 243, 243A, 234, 247, 249, 5101, 5120, 5121 and 5122.
Top and bottom opening is 3-1/2", bulge width is 4-1/2" and is 4-1/16" tall.
Has also been reported to fit Austromax “Aussie Bush Light” very well.
-
-
-
Bail Reproduction - R212
Reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Looks identical to the original.
-
Burner Tube Steel - E233
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long. -
Peerless Mantles 2C-HG - M1
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
Filler Cap Insert 242 Size - S149
Filler cap insert for the models 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. Also fits the model 500 stove. Will have a new gasket installed.
-
Ball Nut 242 Reproduction - S139
Reproduction brass ball nut for the model 242 series lanterns. Look identical to the originals.
-
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
Used Generator Nut - S26
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
Vent Rod Reproduction - S145
Reproduction brass vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.
-
-
Burner Cap Reproduction - S94
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
-
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Mantle Insta-Clip 2 #21 2 pack - M13
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Gas Tip Used - GT24
Used gas tip for 200A5891 generator. Also works well for using on the 220 generators when doing a kerosene conversion.
-
Window Decal - Lantern Green - D101
Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Lantern White - D103
Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal Lantern - Flat Black - D104
Window decal for glass or a hard surface - flat black in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Lantern Red - D102
Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Check Valve O Ring - S36
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
-
Leather Pump Cup Dry - S116
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of dry leather.
-
Window Decal - Sunrise Green - D105
Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Sunrise Red - D106
Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Sunrise White - D107
Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle