237

Products: 150 of 67
Show: 50
  • Filler Cap Gasket for 3 Piece Cap - S41
    • Free Shipping

    Filler Cap Gasket for 3 Piece Cap - S41

    This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

    If your filler cap is a standard size and has a screw in the center then these gaskets will work. 

    Red 3 piece filler cap show for demonstration purposes only.

    Score: 5.00 (votes: 2)
    Reviews: 2
    |
    2
    • $1.25
  • Leather Pump Cup - S81

    This is the common Coleman pump cup that fits most lanterns and stoves. 

    Has a 7/8 inch diameter and is made of oiled leather.

    Score: 3.33 (votes: 3)
    Reviews: 3
    |
    3
    • $3.75
  • Filler Cap Gasket for 1 Piece Cap - S42
    • Free Shipping

    Filler Cap Gasket for 1 Piece Cap - S42

    This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. If your filler cap has a screw in the center of it then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $1.30
  • Check Valve With Stem - C01

    This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part. 


    Also known as part number 2006381ZCL.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $9.40
  • Generator Tube Packing - P05

    This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.

    Not rated yet
    • $2.50
  • Peerless Mantles 111 - M05

    These Peerless mantles are the same size as Coleman #11 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $3.10
  • Large Valve Stem Packing - P01

    Typically used to stop a fuel leak from the valve stem on older appliances.

    This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

    If you need to check your model, please see the PARTS DIAGRAM PAGE

    425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

    Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

    Made of 100% graphite.

    Not rated yet
    • $3.55
  • New Filler Cap Brass - C04

    New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

    Also known as part number 425A1405.

    Not rated yet
    • $9.60
  • Filler Cap Screw 220 Size - S67

    Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

    Fits the cap number: 220C1401

    Not rated yet
    • $1.10
  • Leather Pump Cup And Back-Up Plate - C05
    • New!

    Leather Pump Cup And Back-Up Plate - C05

    Leather pump cup, push on nut and back-up plate. 

    Also known as part number 3000005094.

    Not rated yet
    • $6.45
  • Spark Igniter - E1273

    New Coleman made Spark Igniter. Comes in new packaging with instructions.

    Not rated yet
    • $12.70
  • Graphite Ribbon - P09

    Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

    Not rated yet
    • $5.75
  • Alcohol Bottle - C20

    Alcohol Bottle for kerosene lanterns.

    Not rated yet
    • $7.85
  • Pump Clip Used - S17
    • Free Shipping

    Pump Clip Used - S17

    Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

    Not rated yet
    • $2.00
  • Pump Cup Neoprene - S13

    Pump Cup Neoprene for most lanterns

    Not rated yet
    • $3.55
  • String Tie #11 Mantle - M07

    #11 mantles 2 pack For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles.

    Not rated yet
    • $4.85
  • Pump Screw - S69

    This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

    Not rated yet
    • $0.50
  • Ball Nut 2 Pack - C11

    Ball Nut 2 Pack.


    Also known as part number 3000005384.

    Not rated yet
    • $5.85
  • Check Valve O Ring - S36
    • Free Shipping

    Check Valve O Ring - S36

    Small thin O ring for the common Coleman check valves. Made of gas resistant material.

    Not rated yet
    • $1.10
  • 220 Filler Cap Insert - S144

    This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

    Not rated yet
    • $9.85
  • Generator 237 Kerosene - E1272

    New Generator for Model 237 Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.

    Not rated yet
    • $23.60
  • Ball Nut Used - S18

    Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

    Not rated yet
    • $3.00
  • Globe 237 Clear - G06

    This globe will fit models 236, 237, 237A, 237B 635, 639, 639A, 639B, and 639C.

    Not rated yet
    • $24.15
  • Pump Clip - S22
    • Free Shipping

    Pump Clip - S22

    Pump Clip

    Not rated yet
    • $3.25
  • Valve Wheel Screw Used - S24

    Used valve wheel screw.  Will be in good condition.

    Not rated yet
    • $0.80
  • Pump Assembly Leather Used Square Nut - E1256

    This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

    Not rated yet
    • $13.55
  • Air Stem Used Old Style - S31

    Air stem older style used. Has the larger head on the end.

    In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

    Not rated yet
    • $4.25
  • Filler Cap Tire Valve Brass - R302

    This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

    Not rated yet
    • $13.20
  • Filler Cap Tire Valve Nickel - R301

    This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

    Not rated yet
    • $13.90
  • Pre-Heater Cup - S97

    Pre-heater cup for the model 237 lantern. This is a new production cup made out of brass. It is very high quality and fits the 237 nice and snug. Will also fit a 530 stove if you want to install a PH cup on it.

    Not rated yet
    • $16.60
  • Bail Handle Reproduction - R309

    This is a very nice reproduction bail handle for the model 236 and 237 lanterns. Made of spring steel here in the USA.

    Not rated yet
    • $19.75
  • Decal - Fits 237B Lanterns - D44
    • Free Shipping

    Decal - Fits 237B Lanterns - D44

    Decal for the model 237B kerosene lantern


    Not rated yet
    • $6.35
  • Large Push On Nut for Neoprene Cups - S01
    • Free Shipping

    Large Push On Nut for Neoprene Cups - S01

    Push on nut for pump. The large push on nut is used with the neoprene pump cup.

    Not rated yet
    • $3.25
  • 236 - 237 Burner Tube Brass - E1422

    Brass burner tube for the models 236 and 237.

    Not rated yet
    • $5.40
  • Check Valve Old Style NOS - E1172

    This is the older style check valve that would take the air stem with the larger bulbous end.

    Not rated yet
    • $19.00
  • Vent Rod 236/237 Reproduction - S174

    Reproduction vent rod for the model 236 and 237 lantern. Made of solid brass.

    Not rated yet
    • $10.60
  • Pump Assy Leather Used Push On Nut - E1257

    This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

    Not rated yet
    • $11.95
  • Jamb Nut 530, 237, 249 Reproduction - S157

    Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.

    Not rated yet
    • $7.60
  • Filler Cap Green Used - E1248

    This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.

    Not rated yet
    • $10.00
  • Sparker Flints Zippo - E1270

    Zippo brand Flints for the Coleman Lantern Spark Igniter.

    Not rated yet
    • $4.60
  • Filler Cap Dark Gray Used - E1307

    This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Dark gray in color like the new production Duel Fuel models. 

    Comes with a new gasket for you to install.

    Not rated yet
    • $10.00
  • Spring Clip (Preheater Cup) - S181

    Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111

    Not rated yet
    • $5.45
  • Pump Assembly NOS - E1098
    • New!

    Pump Assembly NOS - E1098

    This is a new old stock pump assembly. Comes with the pump clip. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

    Not rated yet
    • $16.00
  • Valve Wheel Black Square Hole Used - E1427

    Used valve wheel for 201, early 220B's and some model 236 & 237's. In the 426 stove series, this only fits 426 or 426A It fits on valve stems with a square shaft end. It is not interchangeable with other wheels. Will vary in wear.

    Not rated yet
    • $10.00
  • Filler Cap 3 Piece Red Used - E1372

    This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

    We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

     Comes with a new gasket that you will have to install.

    Not rated yet
    • $12.00
  • Generator Tube Packing Used - S193

    Used cardboard tube that goes inside of the 200A and 220 size generators, and many others. 

    Not rated yet
    • $1.00
  • Burner Cap & Screen Reproduction - S93

    New burner cap & screen for the model 236, 237 and 249 lanterns. 

    Solid brass with stainless steel screen.

    Not rated yet
    • $6.25