237A
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
-
Large Valve Stem Packing - P1
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves.
Almost all lantern models use this packing such as 200, 200A, 201, 236, 242, 242A, 242B, 242C, all the 220 and 228 models plus many others. If you need to check your model, please see the PARTS DIAGRAM PAGE.
Coleman made the same product under two different part numbers. This is the same as part number 242-6201.
Made of 100% graphite.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
-
New Filler Cap Brass - C4
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Has gone in the past by part numbers 220C1401, and now 425A1405
-
Generator 237 Kerosene - E11
New Generator for Model 237 Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
-
Pre-Heater Cup - S97
Pre-heater cup for the model 237 lantern. This is a new production cup made out of brass. It is very high quality and fits the 237 nice and snug. Will also fit a 530 stove if you want to install a PH cup on it.
-
Globe 237 Clear - G6
This globe will fit models 236, 237, 237A, 237B 635, 639, 639A, 639B, and 639C.
-
-
Filler Cap Tire Valve Nickel - R218
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Brass - R236
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Tip cleaner - E101
Tip cleaner for the 117A, 118A, 119A, 150B, 150G, 150R, 150I lamps and the 236, 237A, 237B lanterns.
-
-
Filler Cap Red Chipped - E91
Used filler cap that fits most Coleman lanterns and stoves. Paint is chipped with a few wrench marks.
-
-
Peerless Mantles 111 - M5
These Peerless mantles are the same size as Coleman #11 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.
-
Wrench - E806
Old wrench for Coleman lanterns and possibly other brands too. Will show signs of rust. Coleman called this the 605-950 wrench. The ones I have are much better than the one pictured.
-
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
Bail Handle Reproduction - R234
This is a reproduction bail handle for the model 236 and 237 lanterns.
-
Vent Rod 236/237 Reproduction - S174
Reproduction vent rod for the model 236 and 237 lantern. Made of solid brass.
-
Pump Steel Cap NOS - E407
New old stock long pump for the model 220B and 220C lantern. These have a steel cap that connects the pump to the lantern. They have new pump leather on them. Probably made in the 1930's or early 40's.
-
Filler Cap 3 Piece Used Copper Color - E729
This is a used 3 piece filler cap made of brass. Paint is worn and has a new filler cap gasket. Copper in color. Has wrench marks.
-
Filler Cap Red Used - E835
This is a used one piece filler cap. Paint is chipped or missing. Has a new gasket.
-
-
-
-
Pump Brass Cap Used - E185
Used old stock long pump for the model 220B and 220C lantern. These are nickel plated brass but are tarnished with age. Has new pump leather installed. Probably made in the 1930's or early 40's.
-
605 Wrench Used - E956
Used wrench for all Coleman appliances. Used for removing generators and making minor repairs.
-
Window Decal - Lantern Green - D101
Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Lantern White - D103
Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal Lantern - Flat Black - D104
Window decal for glass or a hard surface - flat black in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Lantern Red - D102
Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Check Valve O Ring - S36
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
-
Pump Brass Cap NOS - E243
New old stock long pump for the model 220B and 220C lantern. These have a brass cap that connects the pump to the lantern. They have new pump leather on them. Probably made in the 1930's or early 40's.
-
Leather Pump Cup Dry - S116
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of dry leather.
-
Window Decal - Sunrise Green - D105
Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Sunrise Red - D106
Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Sunrise White - D107
Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2" tall by 3.5" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-