247
-
Check Valve With Stem - C01
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part. The latest part number for this is 2006381ZCL.
-
Generator Lantern - C22
New Generator for 201, 241 and 247 Kerosene Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
-
-
Burner Tube with Nut - Steel - E1127
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
-
Burner Tube Brass - E1269
Burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Filler Cap Gasket - S47
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
-
200A Globe Old Red Logo - G71
This is an used original old red letter logo globe used on lanterns from 1960 to 1980. Although used it will be in good condition. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
-
Burner Cap New - C09
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
-
-
Burner Tube Steel - E1357
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.
-
Ball Nut 242 Reproduction - S139
Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.
-
Pump 242B Used - E1402
Used pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather. Has a double screw holes on the plunger cap.
-
Pre-Heater cup Small - C16
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter. The center hole is larger than needed for the 201 generator. Fits the 214 generator much better.
-
-
Vent Rod Reproduction - S145
Reproduction brass vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.
-
Pump 242B Used Aluminum - E1070
Used pump assembly for the model 242B and early 242C lanterns, also the 243A. Will not work on later models. It has been cleaned and will have a new pump leather. This pump has an aluminum cap.
-
Burner Cap Reproduction - S94
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
-
Valve Used - E1013
Used Valve. Used on model 424. May or may not need a new valve stem packing. If you do the packing is HERE.
-
605 Wrench Used - E1209
Used wrench for all Coleman appliances. Used for removing generators and making minor repairs.
-
200A Globe Clear - G01
New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
-
Reproduction Canadian Ball Nut 242 - R613
Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns.